Epson ActionDesk 4000 User Manual - Page 95

with pin 1 identified at the power connector on the circuit

Get Epson ActionDesk 4000 PDF manuals and user guides View all Epson ActionDesk 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

2. Identify pin 1 on the drive and align the connector so that the red wire is at pin 1, as shown below. Push in the connector. 3. Locate the multi-colored power supply cable with the small connector. This cable is attached to the system board rather than the power supply. 4. Position the power supply cable connector so that the holes fit over all the pins. The red wire on the cable will align with pin 1 identified at the power connector on the circuit board of the drive. Push in the connector. Caution If you do not align the cable connector correctly, you could severely damage your hard disk drive when you push it in. Installing and Removing Drives 5-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
2.
Identify pin 1 on the drive and align the connector so that
the red wire is at pin 1, as shown below. Push in the
connector.
3.
4.
Locate the multi-colored power supply cable with the small
connector. This cable is attached to the system board rather
than the power supply.
Position the power supply cable connector so that the holes
fit over all the pins. The red wire on the cable will align
with pin 1 identified at the power connector on the circuit
board of the drive. Push in the connector.
Caution
If you do not align the cable connector correctly, you could
severely damage your hard disk drive when you push it in.
Installing and Removing Drives
5-19