Epson Endeavor User Manual - Page 137

command. See Resetting, Break], IAft]

Get Epson Endeavor PDF manuals and user guides View all Epson Endeavor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

2. If you have just made a change in your system configuration, your computer may take a few minutes to complete its power-on diagnostics. The first time you turn on your computer after making such a change, it can take several minutes to finish its self test, depending on what you changed. If the computer does not display the operating system prompt after five minutes, turn off the computer, wait 20 seconds, and try again. If that doesn't work, turn off the computer, insert your main operating system diskette or Reference diskette in drive A and turn on the computer. If it still does not boot, contact your Authorized Epson Servicer. 3. Did you enter the correct password? See "Password Problems" below. 4. Could your software be causing the problem? If you are running an application program, see "Software Problems" later in this chapter. 5. The problem could be caused by your keyboard. See "Keyboard Problems" later in this chapter. 6. If you want to stop whatever the computer is doing and return to the MS-DOS command prompt, hold down the [T] key and press (Break] (or Ic]). See Chapter 1 for more information on-stopping a command or program. 7. If your computer still does not respond, you can reset it using the pm7 IAft] [E' command. See "Resetting Your Computer" in Chapter 1 for more information. 8. If resetting the computer does not work, turn off the computer and wait at least 20 seconds. If you do not have a hard disk drive, insert your main operating system diskette in drive A; then turn on the computer. It should load the operating system. 6-8 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
2.
If you have just made a change in your system configuration,
your computer may take a few minutes to complete its
power-on diagnostics. The first time you turn on your
computer after making such a change, it can take several
minutes to finish its self test, depending on what you
changed. If the computer does not display the operating
system prompt after five minutes, turn off the computer,
wait 20 seconds, and try again. If that doesn’t work, turn off
the computer, insert your main operating system diskette
or Reference diskette in drive A and turn on the computer.
If it still does not boot, contact your Authorized Epson
Servicer.
3.
Did you enter the correct password? See “Password
Problems” below.
4.
Could your software be causing the problem? If you are
running an application program, see “Software Problems”
later in this chapter.
5.
The problem could be caused by your keyboard. See
“Keyboard Problems” later in this chapter.
6.
If you want to stop whatever the computer is doing and
return to the MS-DOS command prompt, hold down the
[T]
key and press
(Break]
(or
Ic]).
See Chapter 1 for more
information on-stopping a command or program.
7.
If your computer still does not respond, you can reset it
using the
p7
m
IAft]
[E’
command. See “Resetting
Your Computer” in Chapter 1 for more information.
8.
If resetting the computer does not work, turn off the
computer and wait at least 20 seconds. If you do not have a
hard disk drive, insert your main operating system diskette
in drive A; then turn on the computer. It should load the
operating system.
6-8 Troubleshooting