Home » Epson Manuals » Desktops » Epson Endeavor » Manual Viewer

Epson Endeavor User Manual - Page 46

LOCATING THE INTERNAL COMPONENTS, As you follow the instructions in this refer to

Get Epson Endeavor PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Locating the lnternal Components As you follow the instructions in this chapter, refer to the following illustration to locate the different components inside your computer. Installing and Removing Options 2-3

Section	Page
FRONT MATTER	1
CONTENTS	9
INTRODUCTION	13
VGA UTILITIES	14
OPTIONAL EQUIPMENT	14
MEMORY	14
DRIVES	15
OVER DRIVE PROCESSOR	15
MATH COPROCESSOR	15
ALTERNATE VGA INTERFACE	15
HOW TO USE THIS MANUAL	16
CHAP 1-USING YOUR COMPUTER	17
TURNING ON THE COMPUTER	18
TURNING OFF THE COMPUTER	21
USING DISKS AND DISK DRIVES	21
HOW DISK STORE DATA	22
TYPES OF DISKETTE DRIVES	23
DRIVE AND DISKETTE INCOMPATIBILITIES	24
CARING FOR DISKETTES AND DISKETTE DRIVES	26
WRITE-PROTECTING DISKETTES	28
INSERTING AND REMOVING DISKETTES	30
USING A SINGLE DISKETTE DRIVE SYSTEM	32
FORMATTING DISKETTES	33
MAKING BACKUP COPIES	33
USING A HARD DISK DRIVE	34
BACKING UP THE HARD DISK	35
CARING FOR YOUR HARD DISK	35
SPECIAL KEYS ON THE KEYBOARD	36
STOPPING A COMMAND OR PROGRAM	37
RESETTING THE COMPUTER	38
USING A PASSWORD	39
CHANGING OR DELETING A PASSWORD	39
CHANGING THE PROCESSOR SPEED	40
PREPARING THE HARD DISK FOR MOVING	42
USING AUTOEXEC.BAT AND OTHER BATCH FILES	43
CHAP 2-INSTALLING AND REMOVING OPTIONS	44
HOW TO USE THIS CHAPTER	45
LOCATING THE INTERNAL COMPONENTS	46
REMOVING THE COVER	47
CHANGING THE JUMPER SETTINGS	49
SETTING THE JUMPERS	52
MEMORY MODULES (SIMMS)	54
INSERTING SIMMS	56
REMOVING SIMMS	58
INSTALLING AN OPTION CARD	59
REMOVING AN OPTION CARD	63
REMOVING AN OPTION CARD CONNECTOR BOARD	64
REPLACING THE OPTION CARD CONNECTOR BOARD	65
INSTALLING A NEW PROCESSOR CHIP	66
INCREASING THE VIDEO MEMORY	67
INSTALLING THE MEMORY CHIPS	67
USING THE ALTERNATE VGA INTERFACE	69
USING A DISPLAY ADAPTER CARD	71
REPLACING THE COVER	72
POST-INSTALLATION PROCEDURES	73
CHAP 3-INSTALLING AND REMOVING DRIVES	74
HOW TO USE THIS CHAPTER	76
SETTING THE HARD DISK DRIVE JUMPERS	77
WHERE TO GO NEXT	77
INSTALLING A HARD DISK IN THE VERTICAL BAY	78
REMOVING THE MOUNTING FRAMES	79
INSTALLING THE HARD DISK	81
CONNECTING THE CABLES	85
REMOVING A HARD DISK FROM THE VERTICAL BAY	88
INSTALLING A DRIVE IN A HORIZONTAL BAY	90
ATTACHING MOUNTING FRAMES TO A HARD	92
INSTALLING THE DRIVE	93
CONNECTING THE CABLES	97
REMOVING A DRIVE FROM A HORIZONTAL BUY	102
CONNECTING THE HARD DISK DRIVE RIBBION CABLE TO THE SYSTEM BOARD	106
POST-INSTALLATION PROCEDURES	109
CHAP 4-RUNNING SYSTEM DIAGNOSTICS	110
STARTING THE PROGAM	111
DELETING TESTS	112
ADDING TESTS	113
RUNNING TESTS	114
RESUMING FROM AN ERROR	115
SYSTEM DIAGNOSTIC TESTS	116
ERROR MESSAGES	117
CHAP 5-FORMATTING A HARD DISK	119
STARING THE PROGRAM	120
FORMATTING A NEW DISK	121
REFORMATTING A USED DISK	121
SELECTING AN OPTION	121
SELECTING A DRIVE	122
OPTION 1 FORMAT	122
MODIFYIG THE DEFECTIVE TRACK TABLE	124
FORMATTING THE DISK	126
OPTION 2 DESTRUCTIVE SURFACE ANALYSIS	127
OPTION 3 NON-DESTRUCTIVE SURFACE ANALYSIS	128
EXITING THE PROGRAM	129
CHAP 6-TROUBLESHOOTING	130
INDENTIFYING YOUR SYSTEM	130
ERROR MESSAGES	131
THE COMPUTER WON'T START	135
THE COMPUTER DOES NOT RESPOND	136
RESTORING THE POWER SUPPLY	138
PASSWORD PROBLEMS	139
ACCESSING YOUR SYSTEM	140
KEYBOARD PROBLEMS	141
MONITOR PROBLEMS	142
DISKETTE PROBLEMS	144
DISKETTE DRIVE PROBLEMS	146
HARD DISK PROBLEMS	147
INSTALLING THE DRIVE	147
PREPARING THE DRIVE	148
ACCESSING DATA ON THE DRIVE	149
SOFTWARE PROBLEMS	150
PRINTER PROBLEMS	151
OPTION CARD PROBLEMS	152
MOUSE PROBLEMS	153
MEMORY MODULE PROBLEMS	154
APPENDIX A-SPECIFICATIONS	155
CPU AND MEMORY	155
CONTROLLERS	156
INTERFACES	157
MASS STORAGE	158
KEYBOARD	158
PHYSICAL CHARACTERISTICS	159
POWER SUPPLY	159
ENVIRONMENTAL REQUIREMENTS	160
POWER SOURCE REQUIREMENTS	161
SYSTEM MEMORY MAP	162
GLOSSARY	163