Epson MX-82 F/T User Manual - Page 11

Installation of the Printer

Get Epson MX-82 F/T PDF manuals and user guides View all Epson MX-82 F/T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

3. Installation of the Printer (1) Operating site selection When installing the MX-82, observe the following instructions. (a) Place the Printer on a bench, tabletop or any other convenient flat surface with enough room for the separator in the back of the Printer. Your layout may look like Fig. 3. NOTE: Rubber feet are provided to prevent the marring of the surface where the MX-82 is placed. (b) Avoid operating the MX-82 in places where it may be exposed to direct sunlight or where a great deal of greasy dust exists in the air. NOTE: Greasy dust may cause the malfunction of the print head. (c) Connect the power cord to an outlet separated from those connected to electric noise-generating equipment, such as large-power motors, refrigerators, etc. (d) Do not subject the Printer to temperatures below 5°C (4O'F) or above 35°C (95-F) during operation, to sudden changes in temperature, or to extreme shock. (e) Avoid using the Printer in humid locations or in the vicinity of heat generating sources such as heater, etc. ,i , CRT displav iFloppy disk unit MX-82 / I 2i!!J Interface cable / I Paper / III II Firm surface / - Fig. 3 Laying Printer on Firm Surface -5-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
3. Installation of the Printer
(1) Operating site selection
When installing the MX-82, observe the following instructions.
(a) Place the Printer on a bench, tabletop or any other convenient flat surface
with enough room for the separator in the back of the Printer. Your layout
may look like Fig. 3.
NOTE:
Rubber feet are provided to prevent the marring of the surface where
the MX-82 is placed.
(b) Avoid operating the MX-82 in places where it may be exposed to direct sun-
light or where a great deal of greasy dust exists in the air.
NOTE:
Greasy dust may cause the malfunction of the print head.
(c) Connect the power cord to an outlet separated from those connected to elec-
tric noise-generating equipment, such as large-power motors, refrigerators,
etc.
(d) Do not subject the Printer to temperatures below 5°C
(4O’F)
or above 35°C
(95-F)
during operation, to sudden changes in temperature, or to extreme
shock.
(e) Avoid using the Printer in humid locations or in the vicinity of heat generating
sources such as heater, etc.
CRT
displav
i
Floppy
disk
unit
,,
i
MX-82
/
I
Interface
cable
/
I
/
III
II
2i!!J
Paper
Firm
surface
/
-
Fig. 3 Laying Printer on Firm
Surface
-
5
-