Epson MX-82 F/T User Manual - Page 45

Buzzer, Paper End Detector, to the following status, and the printing operation stops.

Get Epson MX-82 F/T PDF manuals and user guides View all Epson MX-82 F/T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

2. Buzzer The buzzer is located inside the Printer case, and sounds for about one second when the Printer receives BEL code ((07)20H). (See page 66 for the BEL code.) 3. Paper End Detector (1) When the paper end detector (a reed switch located on the paper guide) detects that the paper is nearly exhausted, the signals on the interface connector change to the following status, and the printing operation stops. Table 1 Interface Signals in Paper-Out Status To reactivate the printing, take the following procedure as shown in Fig. 49. t 1 I Push the LF switch (to take out I remaining paper) Buzzer behind) POWER READY I I&-- PAPER OUT 1 - &ONLINE FF Set new paper J PAPER OUT indicator off ON LINE indicator on = ready to restart printing Control panel Fig. 49 Flowchart of Paper Out Status Release Procedure -39-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
2. Buzzer
The buzzer is located inside the Printer case, and sounds for about one second when
the Printer receives BEL code
((07)20H).
(See page 66 for the BEL code.)
3. Paper End Detector
(1) When the paper end detector (a reed switch located on the paper guide) detects
that the paper is nearly exhausted, the signals on the interface connector change
to the following status, and the printing operation stops.
Table 1 Interface Signals in Paper-Out Status
To reactivate the printing, take the following procedure
as
shown in Fig. 49.
Buzzer
behind)
POWER
READY
t
1
I
I&--
PAPER
OUT
I
Push
the
LF
switch
(to
take
out
I
1
-
&ONLINE
remaining
paper)
FF
Set
new
paper
Control panel
J
PAPER OUT indicator off
ON LINE indicator on
= ready to restart printing
Fig. 49 Flowchart of Paper Out Status Release Procedure
-39-