Epson MX-82 F/T User Manual - Page 67

ESC 0, Vertical Tabulation

Get Epson MX-82 F/T PDF manuals and user guides View all Epson MX-82 F/T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

(5) ESC 0 input of the ESC 0 causes the subsequent line spacing to be set at 1/8 inch. (6) ESC2 Input of the ESC 2 causes the subsequent line spacing to be set at either 1/6 inch or 1/8 inch depending on the initial set condition of the DIP switch pin 1-1. (7) VT (Vertical Tabulation) See paragraph 3.1 (3) above. (8) ESC B + nc + n2 + + nk + NUL ( 1 5 k5 8,nks nk+l) This code specifies the vertical tab stop positions. The first 8 valid tab stops per page are recognized in the Printer and subsequent tab stops are ignored. A tab stop set at a line exceeding the form length specified by ESC C + n is ignored. If the form length is set to 66 lines upon initial power application, the last tab stop (nk)n should be less than 66. Tab stop numbers must be received in incremental numerical order. (nk 5 nk+t). To execute tabulation, the VT code should be input. Once vertical tab stops are established, the data will be valid until new tab stops are specified. If no tab stop is set, the VT code behaves like the LF code. Therefore, the paper is advanced one line after printing. Receipt of "ESC B" code causes the Printer to accept the following codes as tab stop line numbers until the NUL code is input. The lack of the NUL code will cause incorrect data printout. The form length must be set by "ESC C + 0 + m" or "ESC C+n" code prior to setting tab stops. The VT setting is cancelled by input of "ESC C + n" code. Therefore, the tab setting should then be established again. Input of "ESC B" code followed by only the NUL code cancels predetermined tab stops. DATA] PRINT] AAAAAiiA .,... 1st line BBBbbBir . . . . . 4th lines CCCCCCC . . . . 6th lines DDDDDDD . 10th lines -61-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
(5) ESC 0
input of the ESC 0 causes the subsequent line spacing to be set at 1/8 inch.
(6) ESC2
Input of the ESC 2 causes the subsequent line spacing to be set at either 1/6
inch or 1/8 inch depending on the initial set condition of the DIP switch pin 1-1.
(7)
VT
(Vertical Tabulation)
See paragraph 3.1 (3) above.
(8)
ESC B +
nc
+
n2
+ +
nk
+ NUL
( 1
5
k5
8,nks
nk+l)
This code specifies the vertical tab stop positions.
The first 8 valid tab stops per page are recognized in the Printer and subse-
quent tab stops are ignored.
A tab stop set at a line exceeding the form length specified by ESC C + n is ig-
nored. If the form length is set to 66 lines upon initial power application, the
last tab stop
(nk)n
should be less than 66.
Tab stop numbers must be received in incremental numerical order.
(nk
5
nk+t).
To execute tabulation, the VT code should be input. Once vertical tab stops are
established, the data will be valid until new tab stops are specified. If no tab
stop is set, the VT code behaves like the LF code. Therefore, the paper is ad-
vanced one line after printing.
Receipt of “ESC B” code causes the Printer to accept the following codes as tab
stop line numbers until the NUL code is input. The lack of the NUL code will
cause incorrect data printout.
The form length must be set by “ESC C + 0 + m” or “ESC C+n” code prior to set-
ting tab stops. The VT setting is cancelled by input of “ESC C + n” code. There-
fore, the tab setting should then be established again. Input of “ESC B” code fol-
lowed by only the NUL code cancels predetermined tab stops.
DATA]
PRINT]
AAAAAiiA
.,...
1st
line
BBBbbBir
.
.
.
.
.
4th
lines
CCCCCCC
.
.
.
.
6th
lines
DDDDDDD
.
10th
lines
-61-