HP 3800 HP Color LaserJet 3000, 3600, 3800 series Printers - User Guide - Page 59

Network configuration, Manually configuring TCP/IP parameters from the printer control panel

Page 59 highlights

Network configuration You might need to configure certain network parameters on the printer. You can configure these parameters from the printer control panel, the embedded Web server, or for most networks, from the HP Web Jetadmin software. NOTE For more information about using the embedded Web server, see Using the embedded Web server. For a complete list of supported networks and for instructions on configuring network parameters from software, see the HP Jetdirect Embedded Print Server Administrator's Guide. The guide comes with printers in which an HP Jetdirect embedded print server is installed. Manually configuring TCP/IP parameters from the printer control panel Use manual configuration to set an IP address, subnet mask, and default gateway. Setting an IP address 1. Press Menu. 2. Press to highlight CONFIGURE DEVICE, and then press . 3. Press to highlight I/O, and then press . 4. Press to highlight EMBEDDED JETDIRECT, and then press . 5. Press to highlight TCP/IP, and then press . 6. Press to select CONFIG METHOD. 7. Press to highlight MANUAL, and then press . 8. Press to highlight MANUAL SETTINGS, and then press . 9. Press to highlight IP Address:, and then press . 10. Press the or arrow to increase or decrease the number for the first byte of the IP address. 11. Press to move to the next set of numbers. (Press to move to the previous set of numbers.) NOTE To cycle through the numbers faster, hold down the arrow button. 12. Repeat steps 10 and 11 until the correct IP address is entered, and then press setting. 13. Press Menu to return to the Ready state. to save the Setting the subnet mask 1. Press Menu. 2. Press to highlight CONFIGURE DEVICE, and then press . 3. Press to highlight I/O, and then press . ENWW Network configuration 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226

Network configuration
You might need to configure certain network parameters on the printer. You can configure these
parameters from the printer control panel, the embedded Web server, or for most networks, from the
HP Web Jetadmin software.
NOTE
For more information about using the embedded Web server, see
Using the embedded
Web server
.
For a complete list of supported networks and for instructions on configuring network parameters from
software, see the
HP Jetdirect Embedded Print Server Administrator’s Guide
. The guide comes with
printers in which an HP Jetdirect embedded print server is installed.
Manually configuring TCP/IP parameters from the printer control
panel
Use manual configuration to set an IP address, subnet mask, and default gateway.
Setting an IP address
1.
Press
Menu
.
2.
Press
to highlight
CONFIGURE DEVICE
, and then press
.
3.
Press
to highlight
I/O
, and then press
.
4.
Press
to highlight
EMBEDDED JETDIRECT
, and then press
.
5.
Press
to highlight
TCP/IP
, and then press
.
6.
Press
to select
CONFIG METHOD
.
7.
Press
to highlight
MANUAL
, and then press
.
8.
Press
to highlight
MANUAL SETTINGS
, and then press
.
9.
Press
to highlight
IP Address:
, and then press
.
10.
Press the
or
arrow to increase or decrease the number for the first byte of the IP address.
11.
Press
to move to the next set of numbers. (Press
to move to the previous set of numbers.)
NOTE
To cycle through the numbers faster, hold down the arrow button.
12.
Repeat steps 10 and 11 until the correct IP address is entered, and then press
to save the
setting.
13.
Press
Menu
to return to the
Ready
state.
Setting the subnet mask
1.
Press
Menu
.
2.
Press
to highlight
CONFIGURE DEVICE
, and then press
.
3.
Press
to highlight
I/O
, and then press
.
ENWW
Network configuration
45