HP DesignJet T1530 User guide - Page 173

Printhead status messages, Missing, Reseat, Replace, Replacement incomplete, Remove, Non-HP ink

Page 173 highlights

4. If the loaded paper is satisfactory, the printer runs the realignment and prints a realignment pattern. 5. The process takes about five minutes. Wait until the front-panel display shows the process complete before using the printer. If the printer cannot complete the printhead alignment successfully, you may be asked to clean the printhead and try again. Printhead status messages These are the possible printhead status messages: ● OK: The printhead is working normally, with no known problems ● Missing: There is no printhead present, or it is not correctly installed in the printer. ● Reseat: You are recommended to remove the printhead and then reinsert it. If that fails, clean the electrical connections, see The front-panel display recommends reseating or replacing the printhead on page 163. If that fails, replace the printhead with a new printhead, see Remove the printhead on page 120 and Insert the printhead on page 122. ● Replace: The printhead is failing. Replace the printhead with a working printhead, see Remove the printhead on page 120 and Insert the printhead on page 122. ● Replacement incomplete: The printhead replacement process has not completed successfully; relaunch the replacement process and let it finish completely. ● Remove: The printhead is not a suitable type for use in printing. ● Non-HP ink: Ink from a used, refilled, or counterfeit ink cartridge has passed through the printhead. See the limited warranty document provided with your printer for details of the warranty implications. ENWW Printhead status messages 165

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198

4.
If the loaded paper is satisfactory, the printer runs the realignment and prints a realignment pattern.
5.
The process takes about
five
minutes. Wait until the front-panel display shows the process complete
before using the printer.
If the printer cannot complete the printhead alignment successfully, you may be asked to clean the printhead
and try again.
Printhead status messages
These are the possible printhead status messages:
OK
: The printhead is working normally, with no known problems
Missing
: There is no printhead present, or it is not correctly installed in the printer.
Reseat
: You are recommended to remove the printhead and then reinsert it. If that fails, clean the
electrical connections, see
The front-panel display recommends reseating or replacing the printhead
on page
163
. If that fails, replace the printhead with a new printhead, see
Remove the printhead
on page
120
and
Insert the printhead
on page
122
.
Replace
: The printhead is failing. Replace the printhead with a working printhead, see
Remove the
printhead
on page
120
and
Insert the printhead
on page
122
.
Replacement incomplete
: The printhead replacement process has not completed successfully; re-
launch the replacement process and let it
finish
completely.
Remove
: The printhead is not a suitable type for use in printing.
Non-HP ink
: Ink from a used,
refilled,
or counterfeit ink cartridge has passed through the printhead. See
the limited warranty document provided with your printer for details of the warranty implications.
ENWW
Printhead status messages
165