HP Integrity Superdome SX1000 SmartSetup Scripting Toolkit Deployment Guide: H - Page 85

efibootmgr Utility Issues, efibootmgr, Active

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

efibootmgr Utility Issues When using the efibootmgr utility, you should be aware of the following issues: • It is possible to create entries to nonexistent boot loaders. • The EFI interface menu is does not accurately indicate the Active/Inactive flag for the boot entries. • The labels of the boot entries are not updated. SSTK Image Does Not Boot and LSI Driver Loops The LSI controller driver does not respond to hardware failures correctly. The SSTK image does not boot and the LSI driver remains in a loop displaying messages similar to the following: target5:0:8: Domain Validation detected failure, dropping back target2:0:0: Domain Validation detected failure, dropping back target2:0:0: Domain Validation detected failure, dropping back target5:0:8: Domain Validation detected failure, dropping back This is an issue with the SCSI MPT-Fusion controller driver that is produced by an improper or defective device. The issue was observed on a LSI1030 that had an Ultra160 disk device improperly configured to at an Ultra320 speed. The problem was corrected by using the EFI driver configuration tool to set the maximum transfer rate to 160Mb/s, which is the speed that the device operates properly . efibootmgr Utility Issues 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
efibootmgr
Utility Issues
When using the
efibootmgr
utility, you should be aware of the following issues:
•
It is possible to create entries to nonexistent boot loaders.
•
The EFI interface menu is does not accurately indicate the
Active
/
Inactive
flag for the
boot entries.
•
The labels of the boot entries are not updated.
SSTK Image Does Not Boot and LSI Driver Loops
The LSI controller driver does not respond to hardware failures correctly. The SSTK image does
not boot and the LSI driver remains in a loop displaying messages similar to the following:
target5:0:8: Domain Validation detected failure, dropping back
target2:0:0: Domain Validation detected failure, dropping back
target2:0:0: Domain Validation detected failure, dropping back
target5:0:8: Domain Validation detected failure, dropping back
This is an issue with the SCSI MPT-Fusion controller driver that is produced by an improper or
defective device. The issue was observed on a LSI1030 that had an Ultra160 disk device improperly
configured to at an Ultra320 speed.
The problem was corrected by using the EFI driver configuration tool to set the maximum transfer
rate to 160Mb/s, which is the speed that the device operates properly .
efibootmgr Utility Issues
85