HP LH4r HP Netserver DiagTools v1.0x User Guide - Page 24

Select/Deselect All Tests in the Highlighted Menu

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Chapter 4 Running DiagTools in the Text Mode (from the Utility Partition) the screen (and in the list shown below). Use the arrow keys to highlight the type of tests you want to run. System Memory IDE FDD (Flexible Disk Drive) SCSI KBD (Keyboard) Video Misc Batch A drop-down menu will display the available individual tests. Once the Advanced System Tests are displayed, you have the following options: Run the Highlighted Test(s) Help Edit Batch Parameters Load Batch Parameters Save Batch Parameters Select/Deselect a Test Select/Deselect All Tests in (the Highlighted) Menu Select/Deselect All Tests List Function Keys Run the Selected Tests Return to Main Menu 1. When the Basic System Tests are completed, you may want to run Advanced System Tests. To do so, navigate back to the Advanced System Test menu. If you receive a message while DiagTools initializes, record and report the message to your support provider. Then press ENTER to proceed. 2. Tests can be run individually or in batches. NOTE For information about using Batch mode when DiagTools is running, choose Batch Help on the Batch submenu. To run any of the tests in the Advanced System Test menu take the following steps: a. Highlight the item you to be tested on the Main Menu. Then press the F6 function key. Check marks appear next to all tests in the highlighted menu, indicating that those tests are selected. b. Press the F10 function key to start the tests. c. Repeat these steps to run any of the following tests as needed: Advanced System Test Menus System Memory 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Chapter 4
Running DiagTools in the Text Mode (from the Utility Partition)
20
the screen (and in the list shown below). Use the arrow keys to highlight the type of tests you want
to run.
System
Memory
IDE
FDD (Flexible Disk Drive)
SCSI
KBD (Keyboard)
Video
Misc
Batch
A drop-down menu will display the available individual tests.
Once the Advanced System Tests are displayed, you have the following options:
<Enter>
Run the Highlighted Test(s)
<F1>
Help
<F2>
Edit Batch Parameters
<F3>
Load Batch Parameters
<F4>
Save Batch Parameters
<F5>
Select/Deselect a Test
<F6>
Select/Deselect All Tests in (the Highlighted) Menu
<F7>
Select/Deselect All Tests
<F9>
List Function Keys
<F10>
Run the Selected Tests
<Esc>
Return to Main Menu
1.
When the Basic System Tests are completed, you may want to run Advanced System Tests.
To do so, navigate back to the Advanced System Test menu.
If you receive a message while DiagTools initializes, record and report the message to your
support provider. Then press ENTER to proceed.
2.
Tests can be run individually or in batches.
NOTE
For information about using Batch mode when DiagTools is running, choose
Batch Help
on the Batch submenu.
To run any of the tests in the Advanced System Test menu take the following steps:
a.
Highlight the item you to be tested on the Main Menu. Then press the F6 function key.
Check marks appear next to all tests in the highlighted menu, indicating that those tests
are selected.
b.
Press the F10 function key to start the tests.
c.
Repeat these steps to run any of the following tests as needed:
Advanced System Test Menus
System
Memory