HP LH4r HP Netserver DiagTools v1.0x User Guide - Page 44

Check system fans. If overheating occurs, chip may shut down.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Chapter 5 Error Message Reference Code 00A7h 00B1h 00B2h 00B3h Description NVRAM test failed. PNP header not found PNP function 50h execution failed. PNP function 51h execution failed. Recommended Action restart. 11. If system repeatedly shows this error, replace the element with the CMOS. 1. Run the BIOS Setup program and reconfigure all settings. 2. If necessary, update the BIOS. 3. Clear the CMOS and rerun configuration. See directions on the technical reference label or card. 4. Make sure the system board is seated. 5. Check the seating of the voltage regulator module (VRM) if present. 6. Be sure the processor board (if any) is seated. 7. Make sure the CPU chip is seated. (Take ESD precautions.) 8. Make sure the memory elements (DIMMs) are properly seated. 9. Check system fans. If overheating occurs, chip may shut down. 10. If the system ran with temperature high, let it cool for 30 minutes, then restart. 11. If system repeatedly shows this error, replace the element with the CMOS. 1. Run the BIOS Setup program and reconfigure all settings. 2. If necessary, update the BIOS. 3. Clear the CMOS and rerun configuration. See directions on the technical reference label or card. 4. Make sure the system board is seated. 5. Check the seating of the voltage regulator module (VRM) if present. 6. Be sure the processor board (if any) is seated. 7. Make sure the CPU chip is seated. (Take ESD precautions.) 8. Make sure the memory elements (DIMMs) are properly seated. 9. Check system fans. If overheating occurs, chip may shut down. 10. If the system ran with temperature high, let it cool for 30 minutes, then restart. 11. If system repeatedly shows this error, replace the element with the CMOS. 1. Run the BIOS Setup program and reconfigure all settings. 2. If necessary, update the BIOS. 3. Clear the CMOS and rerun configuration. See directions on the technical reference label or card. 4. Make sure the system board is seated. 5. Check the seating of the voltage regulator module (VRM) if present. 6. Be sure the processor board (if any) is seated. 7. Make sure the CPU chip is seated. (Take ESD precautions.) 8. Make sure the memory elements (DIMMs) are properly seated. 9. Check system fans. If overheating occurs, chip may shut down. 10. If the system ran with temperature high, let it cool for 30 minutes, then restart. 11. If system repeatedly shows this error, replace the element with the CMOS. 1. Run the BIOS Setup program and reconfigure all settings. 2. If necessary, update the BIOS. 3. Clear the CMOS and rerun configuration. See directions on the technical 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Chapter 5
Error Message Reference
40
Code
Description
Recommended Action
restart.
11. If system repeatedly shows this error, replace the element with the CMOS.
00A7h
NVRAM test failed.
1. Run the BIOS Setup program and reconfigure all settings.
2. If necessary, update the BIOS.
3. Clear the CMOS and rerun configuration. See directions on the technical
reference label or card.
4. Make sure the system board is seated.
5. Check the seating of the voltage regulator module (VRM) if present.
6. Be sure the processor board (if any) is seated.
7. Make sure the CPU chip is seated. (Take ESD precautions.)
8. Make sure the memory elements (DIMMs) are properly seated.
9. Check system fans. If overheating occurs, chip may shut down.
10. If the system ran with temperature high, let it cool for 30 minutes, then
restart.
11. If system repeatedly shows this error, replace the element with the CMOS.
00B1h
PNP header not
found
1. Run the BIOS Setup program and reconfigure all settings.
2. If necessary, update the BIOS.
3. Clear the CMOS and rerun configuration. See directions on the technical
reference label or card.
4. Make sure the system board is seated.
5. Check the seating of the voltage regulator module (VRM) if present.
6. Be sure the processor board (if any) is seated.
7. Make sure the CPU chip is seated. (Take ESD precautions.)
8. Make sure the memory elements (DIMMs) are properly seated.
9. Check system fans. If overheating occurs, chip may shut down.
10. If the system ran with temperature high, let it cool for 30 minutes, then
restart.
11. If system repeatedly shows this error, replace the element with the CMOS.
00B2h
PNP function 50h
execution failed.
1. Run the BIOS Setup program and reconfigure all settings.
2. If necessary, update the BIOS.
3. Clear the CMOS and rerun configuration. See directions on the technical
reference label or card.
4. Make sure the system board is seated.
5. Check the seating of the voltage regulator module (VRM) if present.
6. Be sure the processor board (if any) is seated.
7. Make sure the CPU chip is seated. (Take ESD precautions.)
8. Make sure the memory elements (DIMMs) are properly seated.
9. Check system fans. If overheating occurs, chip may shut down.
10. If the system ran with temperature high, let it cool for 30 minutes, then
restart.
11. If system repeatedly shows this error, replace the element with the CMOS.
00B3h
PNP function 51h
execution failed.
1. Run the BIOS Setup program and reconfigure all settings.
2. If necessary, update the BIOS.
3. Clear the CMOS and rerun configuration. See directions on the technical