HP LH4r HP Netserver DiagTools v2.0 User Guide - Page 59

Misc Tests

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 5 Error Message Reference Code 0560h 0580h 0590h Description DiagTools Error DOS Memory Allocation Error. SCSI command not supported by this device. Recommended Action between cards and backplane. 2. Inspect SCSI pins to ensure none are bent. 3. Check seating of board or SCSI card. 4. Check for proper termination, using technical reference card or label. 5. Check system fans 6. Check firmware version of drive and update if necessary. 7. Replace the drive 8. Change the card or board that has the drive's controller. Download a new version of DiagTools from the HP web site and run it. If you get the same error, call the HP Customer Care Center. The SCSI diagnostic does not have enough memory to run. This is generally caused by having multiple types of SCSI controller in the system--for instance, Adaptec, Symbios, and NetRAID. Each controller type requires a separate driver to be loaded in memory. Reduce the number of different types of SCSI controller active in the system-either by disabling internal controllers via Setup, or by removing any plug-in SCSI controllers, or by removing all NetRAID cards. Then rerun the test. The device you are testing does not support the SCSI commands required by this diagnostic. If the device is an HP-supported device, report the error to an HP Customer Care Center. Misc Tests The Misc Test Menu includes testing of the serial port with a series of tests designed to ensure complete functionality is present. A similar specific set of tests is present for parallel ports. Code Description Recommended Action 0601h 0602h 0603h 0604h 0605h 0606h 0607h 0608h 0609h 0610h Serial Port Test Failed Interrupt identification register test failed. DiagTools Error Line status register test failed at port XXXXh. Interrupt activation test failed at port XXXXh. DiagTools Error DiagTools Error FIFO register test failed at port XXXXh. FIFO trigger level test failed at port XXXXh. FIFO character timeout indication Possible system board failure. Possible system board failure. Report error to HP Customer Care Center and get the latest version of DiagTools. Possible system board failure. Possible system board failure. Report error to HP Customer Care Center and get the latest version of DiagTools. Report error to HP Customer Care Center and get the latest version of DiagTools. Possible system board failure. Possible system board failure. Possible system board failure. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Chapter 5
Error Message Reference
55
Code
Description
Recommended Action
between cards and backplane.
2. Inspect SCSI pins to ensure none are bent.
3. Check seating of board or SCSI card.
4. Check for proper termination, using technical reference card or label.
5. Check system fans
6. Check firmware version of drive and update if necessary.
7. Replace the drive
8. Change the card or board that has the drive’s controller.
0560h
DiagTools Error
Download a new version of DiagTools from the HP web site and run it. If you
get the same error, call the HP Customer Care Center.
0580h
DOS Memory
Allocation Error.
The SCSI diagnostic does not have enough memory to run. This is generally
caused by having multiple types of SCSI controller in the system--for instance,
Adaptec, Symbios, and NetRAID. Each controller type requires a separate driver
to be loaded in memory.
Reduce the number of different types of SCSI controller active in the system--
either by disabling internal controllers via Setup, or by removing any plug-in
SCSI controllers, or by removing all NetRAID cards. Then rerun the test.
0590h
SCSI command not
supported by this
device.
The device you are testing does not support the SCSI commands required by this
diagnostic. If the device is an HP-supported device, report the error to an HP
Customer Care Center.
Misc Tests
The Misc Test Menu includes testing of the serial port with a series of tests designed to ensure complete
functionality is present. A similar specific set of tests is present for parallel ports.
Code
Description
Recommended Action
0601h
Serial Port Test
Failed
Possible system board failure.
0602h
Interrupt
identification
register test failed.
Possible system board failure.
0603h
DiagTools Error
Report error to HP Customer Care Center and get the latest version of DiagTools.
0604h
Line status register
test failed at port
XXXXh.
Possible system board failure.
0605h
Interrupt activation
test failed at port
XXXXh.
Possible system board failure.
0606h
DiagTools Error
Report error to HP Customer Care Center and get the latest version of DiagTools.
0607h
DiagTools Error
Report error to HP Customer Care Center and get the latest version of DiagTools.
0608h
FIFO register test
failed at port
XXXXh.
Possible system board failure.
0609h
FIFO trigger level
test failed at port
XXXXh.
Possible system board failure.
0610h
FIFO character
timeout indication
Possible system board failure.