HP LH4r HP Netserver DiagTools v2.0 User Guide - Page 7

Hardware Detection, About Error Messages, Advantages and Limitations of Hardware Diagnostics

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Chapter 1 DiagTools Overview If you have TopTools remote management software installed and configured for use with DiagTools, you can accomplish any of the above tasks remotely. In order to do so, use the text-based DiagTools installed on the Utility Partition of the system to be tested, and use ERA and RMC to access the partition and redirect the console. Note When MC is used , colors are not standard VGA, so text may not be readable. DiagTools User Interface Modes: Graphical or Text-Based DiagTools has two different types of interface modes. The graphical interface operates from a DiagTools diskette made while HP NetServer Navigator is running. The text-based mode operates when the Utility Partition is installed. In order for DiagTools to be run remotely, it must be installed on the Utility Partition of the NetServer. For more details, see the section of chapter 2 entitled "Preparing for Remote Operation" and the section of chapter 4 entitled "Before You Begin . . .." Hardware Detection Overview of Configuration Detection Configuration detection determines which tests are appropriate for your HP NetServer. For example, if your server has an IDE or SCSI hard disk, the boot sector of the disk will be checked as part of the basic system test. In the Advanced System Tests, some functions will be disabled if they are not appropriate for your NetServer. For example, if you do not have a SCSI controller (or if your SCSI controller is not responding), the SCSI menu in the Advanced System Tests will be disabled. What is Detected A list of items detected is shown in Table 1-2. About Error Messages Each error message in DiagTools is designated by a hexadecimal number, a short note on the type of error, and a list of one or more steps the user can take in response. When you run a test, it exercises many aspects of the hardware, so the number of possible error messages exceeds 300. Most of these are encountered rarely, if ever. You can view error codes on line from the Misc Menu of the Advanced System Tests, or you can refer to Chapter 5 of this guide, which lists the error messages in alphanumeric order. Advantages and Limitations of Hardware Diagnostics Off-line diagnostic software is useful in making sure that hardware has been eliminated as the cause for possible system problems. Such diagnostic tools are easy to use. However,diagnostic software should only be used by experienced personnel who can take a wider view of its limitations, which include: • rebooting the server one or more times whenever off-line diagnostics are run • an offline diagnostic runs on the system under test, meaning it cannot control and observe all aspects of that system 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Chapter 1
DiagTools Overview
3
If you have TopTools remote management software installed and configured for use with DiagTools, you
can accomplish any of the above tasks remotely. In order to do so, use the text-based DiagTools installed on
the Utility Partition of the system to be tested, and use ERA and RMC to access the partition and redirect
the console.
Note
When MC is used , colors are not standard VGA, so text may not be readable.
DiagTools User Interface Modes: Graphical or Text-Based
DiagTools has two different types of interface modes. The graphical interface operates from a DiagTools
diskette made while HP NetServer Navigator is running. The text-based mode operates when the Utility
Partition is installed. In order for DiagTools to be run remotely, it must be installed on the Utility Partition
of the NetServer. For more details, see the section of chapter 2 entitled “Preparing for Remote Operation”
and the section of chapter 4 entitled “Before You
Begin . . ..”
Hardware Detection
Overview of Configuration Detection
Configuration detection determines which tests are appropriate for your HP NetServer. For example, if your
server has an IDE or SCSI hard disk, the boot sector of the disk will be checked as part of the basic system
test.
In the Advanced System Tests, some functions will be disabled if they are not appropriate for your
NetServer. For example, if you do not have a SCSI controller (or if your SCSI controller is not responding),
the SCSI menu in the Advanced System Tests will be disabled.
What is Detected
A list of items detected is shown in Table 1-2.
About Error Messages
Each error message in DiagTools is designated by a hexadecimal number, a short note on the type of error,
and a list of one or
more steps the user can take in response. When you run a test, it exercises many aspects
of the hardware, so the number of possible error messages exceeds 300. Most of these are encountered
rarely, if ever.
You can view error codes on line from the Misc Menu of the Advanced System Tests, or you can refer to
Chapter 5 of this guide, which lists the error messages in alphanumeric order.
Advantages and Limitations of Hardware Diagnostics
Off-line diagnostic software is useful in making sure that hardware has been eliminated as the cause for
possible system problems. Such diagnostic tools are easy to use. However,diagnostic software should only be
used by experienced personnel who can take a wider view of its limitations, which include:
•
rebooting the server one or more times whenever off-line diagnostics are run
•
an offline diagnostic runs on the system under test, meaning it cannot control and observe all aspects
of that system