HP OMEN Transcend 16 Maintenance and Service Guide - Page 53

USB board, Remove the Phillips M2.0 × 3.5 screw

Get HP OMEN Transcend 16 PDF manuals and user guides View all HP OMEN Transcend 16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

USB board To remove the USB board, use this procedure and illustration. Table 6-7 USB board description and part number Description USB board USB board cable Spare part number N43736-001 N43722-001 Before removing the USB board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 37). 2. Remove the bottom cover (see Bottom cover on page 37). Remove the USB board: 1. Disconnect the cable from the ZIF connector on the USB board (1). 2. Remove the Phillips M2.0 × 3.5 screw (2) that secures the board to the computer. 3. Remove the tape from the right side of the board (3). 4. Remove the board (4). To install the USB board, reverse this procedure. When installing a USB board, insert it at an angle and so that the end of the board is under the hook that holds it in place, and then press the board down into place. 46 Chapter 6 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
USB board
To remove the USB board, use this procedure and illustration.
Table 6-7
USB board description and part number
Description
Spare part number
USB board
N43736-001
USB board cable
N43722-001
Before removing the USB board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
37
).
2.
Remove the bottom cover (see
Bottom cover
on page
37
).
Remove the USB board:
1.
Disconnect the cable from the ZIF connector on the USB board
(1)
.
2.
Remove the Phillips M2.0 × 3.5 screw
(2)
that secures the board to the computer.
3.
Remove the tape from the right side of the board
(3)
.
4.
Remove the board
(4)
.
To install the USB board, reverse this procedure.
When installing a USB board, insert it at an angle and so that the end of the board is under the hook that
holds it in place, and then press the board down into place.
46
Chapter 6
Removal and replacement procedures for authorized service provider parts