HP OmniBook 900 HP OmniBook 900 - Docking System User Guide - Page 51

Installing PC Devices

Get HP OmniBook 900 - Notebook PC PDF manuals and user guides View all HP OmniBook 900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Installing Accessories Installing PC Devices You can install either a 5 ¼ inch PC device or a 3 ½ inch device such as a hard disk drive in the PC device bay. The bay supports both IDE and SCSI-2 devices. Refer to the instructions that came with your PC device for any device-specific installation instructions. . Before Installing an IDE device Refer to the IDE device's manual to see if you must set jumpers or if there is a special installation procedure to follow. If you have the option of selecting Master, Slave, or Cable Select setting, select Master for the IDE device. . Before installing a SCSI device Before installing a SCSI device in your dock, assign an unused SCSI address to the device. The dock supports 8-bit (narrow) SCSI addresses with values from 0 to 6. SCSI address 7 is reserved for the integrated SCSI controller. . Both the SCSI port on the rear of the dock and the PC device bay SCSI cable are on a single SCSI bus. All SCSI devices must have a unique address. Refer to the installation guide provided with the device for information on selecting a SCSI address. . SCSI devices installed in the PC device bay must be terminated. Refer to the device's installation guide for details. 1-51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Installing Accessories
1-51
Installing PC Devices
You can install either a 5 ¼ inch PC device or a 3 ½ inch device such as a hard disk
drive in the PC device bay. The bay supports both IDE and SCSI-2 devices.
Refer to the instructions that came with your PC device for any device-specific
installation instructions. .
Before Installing an IDE device
Refer to the IDE device’s manual to see if you must set jumpers or if there is a
special installation procedure to follow. If you have the option of selecting Master,
Slave, or Cable Select setting, select Master for the IDE device. .
Before installing a SCSI device
Before installing a SCSI device in your dock, assign an unused SCSI address to the
device. The dock supports 8-bit (narrow) SCSI addresses with values from 0 to 6.
SCSI address 7 is reserved for the integrated SCSI controller. . Both the SCSI port on
the rear of the dock and the PC device bay SCSI cable are on a single SCSI bus. All
SCSI devices must have a unique address. Refer to the installation guide provided
with the device for information on selecting a SCSI address. .
SCSI devices installed in the PC device bay must be terminated. Refer to the device’s
installation guide for details.