HP Workstation x2000 ATI Fire GL 8800 graphics card user guide - Page 28

Start > Settings > Control Panel > Display &gt, ATI FGL Install

Get HP Workstation x2000 PDF manuals and user guides View all HP Workstation x2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

24 Installing the Hardware and Software 4 Click the button corresponding to the type of installation you want. If you select Custom, a list of software components will be displayed. Select the check boxes to specify the components you want to install. 5 Click Next to continue the installation. 6 When the ATI FGL Install dialog displays the components to be installed click on Next. (Depending on which components you chose different windows might appear. Click on the corresponding buttons to continue the installation.) 7 When the Installation complete message appears click Next again. This will restart your computer. 8 After Windows 2000/Windows XP reboots, the Found New Hardware message displays the Digital Signature Not Found dialog and prompts you Do you want to continue the installation? Click Yes to install and start the drivers. 9 Click Start > Settings > Control Panel > Display > Settings, or right-click on the Windows desktop, select Properties and Settings. 10 Set the resolution (Screen area), and color depth that best suit your requirements and your monitor's performance. 11 Click the Advanced button and select the Monitor tab. 12 Set the refresh rate for the monitor connected to the Fire GL 8800 graphics accelerator in your system. Note: If you have two monitors connected this setting applies to the monitor connected to the VGA connector. Use the ATI Monitor and DualScreen dialogs to adapt each monitor's settings in a dual-monitor configuration. 13 Click OK until you are on the Windows desktop. Note Refer to your Windows online help and documentation for further information on using the Monitor and Settings dialogs.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
24
Installing the Hardware and Software
4
Click the button corresponding to the type of installation you
want. If you select
Custom
, a list of software components will
be displayed. Select the check boxes to specify the components
you want to install.
5
Click
Next
to continue the installation.
6
When the
ATI FGL Install
dialog displays the components to be
installed click on
Next
. (Depending on which components you
chose different windows might appear. Click on the
corresponding buttons to continue the installation.)
7
When the
Installation complete
message appears click
Next
again. This will restart your computer.
8
After Windows 2000/Windows XP reboots, the
Found New
Hardware
message displays the
Digital Signature Not
Found
dialog and prompts you
Do you want to continue
the installation?
Click
Yes
to install and start the drivers.
9
Click
Start > Settings > Control Panel > Display >
Settings
, or right-click on the Windows desktop, select
Properties
and
Settings
.
10
Set the resolution (
Screen area
), and color depth that best suit
your requirements and your monitor's performance.
11
Click the
Advanced
button and select the
Monitor
tab.
12
Set the refresh rate for the monitor connected to the Fire GL
8800 graphics accelerator in your system.
Note
:
If you have two monitors connected this setting applies to
the monitor connected to the VGA connector. Use the
ATI
Monitor
and
DualScreen
dialogs to adapt each monitor's
settings in a dual-monitor configuration.
13
Click
OK
until you are on the Windows desktop.
Note
Refer to your Windows online help and documentation for
further information on using the
Monitor
and
Settings
dialogs.