IBM JS20 User Guide - Page 35

Attention

Get IBM JS20 - BladeCenter - 8842 PDF manuals and user guides
UPC - 000435230263
View all IBM JS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Attention: To maintain proper system cooling, do not operate the BladeCenter unit for more than 1 minute without a blade server or filler blade installed in each blade bay. IDE drive Tray Riser card IDE connector 2 (J2) Short screws IDE connector 1 (J1) Attention: v Drives must be installed in the following order: IDE connector 1 (J1) first, then IDE connector 2 (J2). v Do not install a hard disk drive in IDE connector 2 if you intend to also install an optional I/O expansion card. The I/O expansion card occupies the same area as the second IDE hard disk drive. v Do not press on the top of the hard disk drive when installing it. Pressing the top could damage the hard disk drive. v IDE hard disk drives must be set to primary (master). See the documentation that came with your hard disk drive for instructions. Complete the following steps to install a 2.5-inch IDE hard disk drive: 1. Read the safety information beginning on page v and "Installation guidelines" on page 19. 2. If the blade server is operating, shut down the operating system by typing the shutdown -h now command. If the blade server was not turned off, press the power-control button (behind the blade-server control-panel door) to turn off the blade server. See "The control panel buttons and LEDs" on page 13 for more information about the location of the power-control button. 3. Remove the blade server from the BladeCenter unit. (See "Removing the blade server from the BladeCenter unit" on page 21 for instructions.) Carefully place the blade server on a flat, static-protective surface. 4. Open the blade server cover. See "Opening the blade server cover" on page 22 for instructions. 5. Insert the riser card from the option kit into an IDE connector on the blade server system board. Chapter 4. Installing options 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Attention:
To
maintain
proper
system
cooling,
do
not
operate
the
BladeCenter
unit
for
more
than
1
minute
without
a
blade
server
or
filler
blade
installed
in
each
blade
bay.
IDE drive
Tray
Riser
card
Short screws
IDE connector 1
(J1)
IDE connector 2
(J2)
Attention:
v
Drives
must
be
installed
in
the
following
order:
IDE
connector
1
(J1)
first,
then
IDE
connector
2
(J2).
v
Do
not
install
a
hard
disk
drive
in
IDE
connector
2
if
you
intend
to
also
install
an
optional
I/O
expansion
card.
The
I/O
expansion
card
occupies
the
same
area
as
the
second
IDE
hard
disk
drive.
v
Do
not
press
on
the
top
of
the
hard
disk
drive
when
installing
it.
Pressing
the
top
could
damage
the
hard
disk
drive.
v
IDE
hard
disk
drives
must
be
set
to
primary
(master).
See
the
documentation
that
came
with
your
hard
disk
drive
for
instructions.
Complete
the
following
steps
to
install
a
2.5-inch
IDE
hard
disk
drive:
1.
Read
the
safety
information
beginning
on
page
v
and
“Installation
guidelines”
on
page
19.
2.
If
the
blade
server
is
operating,
shut
down
the
operating
system
by
typing
the
shutdown
-h
now
command.
If
the
blade
server
was
not
turned
off,
press
the
power-control
button
(behind
the
blade-server
control-panel
door)
to
turn
off
the
blade
server.
See
“The
control
panel
buttons
and
LEDs”
on
page
13
for
more
information
about
the
location
of
the
power-control
button.
3.
Remove
the
blade
server
from
the
BladeCenter
unit.
(See
“Removing
the
blade
server
from
the
BladeCenter
unit”
on
page
21
for
instructions.)
Carefully
place
the
blade
server
on
a
flat,
static-protective
surface.
4.
Open
the
blade
server
cover.
See
“Opening
the
blade
server
cover”
on
page
22
for
instructions.
5.
Insert
the
riser
card
from
the
option
kit
into
an
IDE
connector
on
the
blade
server
system
board.
Chapter
4.
Installing
options
23