IBM JS20 User Guide - Page 78

Error, Failing, device, problem, found, Suggested, action, ibm,fw-fcpdisk, setup-fc-disk

Get IBM JS20 - BladeCenter - 8842 PDF manuals and user guides
UPC - 000435230263
View all IBM JS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Table 1. Abbreviated list of firmware error codes (continued) Error code Failing device or problem found Suggested action 20A80005 The trivial file transfer protocol (TFTP) failed. 1. Make sure that the BOOTP server is correctly configured for this client. 2. Check the network connection. If the network connection is good, retry the operation. If there is no network connection, contact your network administrator. 3. If there are no problems with the BOOTP server or the network connection, replace the system-board assembly. Contact a service support representative for more information. 20A80006 The startup image is too large. 1. Make sure that the BOOTP server is correctly configured for this client. 2. Check the network connection. If the network connection is good, retry the operation. If there is no network connection, contact your network administrator. 3. If there are no problems with the BOOTP server or the network connection, replace the system-board assembly. Contact a service support representative for more information. 20A80100 A SAN device was found in the boot list; however, the ibm,fw-fcpdisk alias name has not been defined in the /alias node. Type the setup-fc-disk command at the open firmware prompt and press Enter; then, restart the blade server. 20A80102 The ibm,fw-fcpdisk alias is not a SAN device. Run the setup-fc-disk utility. 20A80104 The disk2 alias was found and This is an informational message. No action is required. copied to the ibm,fw-fcpdisk alias. 20A80110 The ibm,fw-fcpdisk alias was modified. This is an informational message. No action is required. 20D0000F The device failed the self-test; error v If a location code is specified, replace the device at that or location code information might not location. be available. v Perform the system checkout procedure. See "System checkout" on page 48. 20D00010 The device failed the self-test; cannot 1. If a location code is reported with the error, replace locate package. the device at that location code. 2. Replace the system-board assembly. Contact a service support representative for more information. 20D00011 The run-time extraction services (RTAS) program attempt to allocate memory failed. Perform the system checkout procedure. See "System checkout" on page 48. 66 BladeCenter JS20 Type 8842: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Table
1.
Abbreviated
list
of
firmware
error
codes
(continued)
Error
code
Failing
device
or
problem
found
Suggested
action
20A80005
The
trivial
file
transfer
protocol
(TFTP)
failed.
1.
Make
sure
that
the
BOOTP
server
is
correctly
configured
for
this
client.
2.
Check
the
network
connection.
If
the
network
connection
is
good,
retry
the
operation.
If
there
is
no
network
connection,
contact
your
network
administrator.
3.
If
there
are
no
problems
with
the
BOOTP
server
or
the
network
connection,
replace
the
system-board
assembly.
Contact
a
service
support
representative
for
more
information.
20A80006
The
startup
image
is
too
large.
1.
Make
sure
that
the
BOOTP
server
is
correctly
configured
for
this
client.
2.
Check
the
network
connection.
If
the
network
connection
is
good,
retry
the
operation.
If
there
is
no
network
connection,
contact
your
network
administrator.
3.
If
there
are
no
problems
with
the
BOOTP
server
or
the
network
connection,
replace
the
system-board
assembly.
Contact
a
service
support
representative
for
more
information.
20A80100
A
SAN
device
was
found
in
the
boot
list;
however,
the
ibm,fw-fcpdisk
alias
name
has
not
been
defined
in
the
/alias
node.
Type
the
setup-fc-disk
command
at
the
open
firmware
prompt
and
press
Enter;
then,
restart
the
blade
server.
20A80102
The
ibm,fw-fcpdisk
alias
is
not
a
SAN
device.
Run
the
setup-fc-disk
utility.
20A80104
The
disk2
alias
was
found
and
copied
to
the
ibm,fw-fcpdisk
alias.
This
is
an
informational
message.
No
action
is
required.
20A80110
The
ibm,fw-fcpdisk
alias
was
modified.
This
is
an
informational
message.
No
action
is
required.
20D0000F
The
device
failed
the
self-test;
error
or
location
code
information
might
not
be
available.
v
If
a
location
code
is
specified,
replace
the
device
at
that
location.
v
Perform
the
system
checkout
procedure.
See
“System
checkout”
on
page
48.
20D00010
The
device
failed
the
self-test;
cannot
locate
package.
1.
If
a
location
code
is
reported
with
the
error,
replace
the
device
at
that
location
code.
2.
Replace
the
system-board
assembly.
Contact
a
service
support
representative
for
more
information.
20D00011
The
run-time
extraction
services
(RTAS)
program
attempt
to
allocate
memory
failed.
Perform
the
system
checkout
procedure.
See
“System
checkout”
on
page
48.
66
BladeCenter
JS20
Type
8842:
Installation
and
User’s
Guide