IBM x3500 User Guide - Page 42

Installing, full-high, drive

Get IBM x3500 - System - 7977 PDF manuals and user guides
UPC - 883436005760
View all IBM x3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installing a full-high tape drive EMC shields Tape drive To install a full-high tape drive, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 21. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables necessary to replace the device. 3. Unlock and remove the left-side cover (see "Removing the left-side cover" on page 24). 4. Press on the bezel retention tab at the center-left-edge of the bezel, and rotate the left side of the bezel away from the server; then, pull the bezel away from the server. 5. Connect the full-high tape drive cable to the system board. 6. Slide the drive into the server and connect the IDE cable to the drive. 7. Using the supplied screws, secure the drive to the server chassis. 8. Replace the left-side cover and bezel; then, lock the side cover and bezel. 9. Reconnect the external cables and power cords. If you have other optional devices to install or remove, do so now. Otherwise, go to "Completing the installation" on page 46. 28 IBM System x3500 Type 7977: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Installing
a
full-high
tape
drive
Tape drive
EMC shields
To
install
a
full-high
tape
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
21.
2.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables
necessary
to
replace
the
device.
3.
Unlock
and
remove
the
left-side
cover
(see
“Removing
the
left-side
cover”
on
page
24).
4.
Press
on
the
bezel
retention
tab
at
the
center-left-edge
of
the
bezel,
and
rotate
the
left
side
of
the
bezel
away
from
the
server;
then,
pull
the
bezel
away
from
the
server.
5.
Connect
the
full-high
tape
drive
cable
to
the
system
board.
6.
Slide
the
drive
into
the
server
and
connect
the
IDE
cable
to
the
drive.
7.
Using
the
supplied
screws,
secure
the
drive
to
the
server
chassis.
8.
Replace
the
left-side
cover
and
bezel;
then,
lock
the
side
cover
and
bezel.
9.
Reconnect
the
external
cables
and
power
cords.
If
you
have
other
optional
devices
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
46.
28
IBM
System
x3500
Type
7977:
User’s
Guide