IBM x3500 User Guide - Page 55

Vacuum tool, Microprocessor, Socket

Get IBM x3500 - System - 7977 PDF manuals and user guides
UPC - 883436005760
View all IBM x3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Vacuum tool Microprocessor Socket a. Squeeze and hold the bladder of the tool; then, place the suction cup on the microprocessor and release the bladder. Note: To maintain proper orientation between the microprocessor and the microprocessor socket during installation, observe the following information: v The microprocessor has two notches that are keyed to two tabs on the sides of the socket. v A triangle-shaped indicator on one corner of the microprocessor points to a 45-degree angle on one corner of the socket. b. Using the tool, carefully place the microprocessor into the socket. c. Squeeze the bladder of the tool to release the microprocessor from the suction cup. 7. Close the microprocessor bracket frame; then, close the microprocessor retention latch and lock it securely in place. 8. Close the microprocessor-release lever to secure the microprocessor. 9. Make sure that the heat-sink release lever is open. 10. If necessary, remove the cover from the bottom of the heat sink. 11. Place the tab on the heat sink into the connector in the retention bracket; then, rotate the heat sink into place and close the heat-sink release lever. Note: If you are installing an additional microprocessor in microprocessor socket 2, you must also install a VRM. 12. If necessary, install a VRM in the connector. Chapter 2. Installing optional devices 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Vacuum tool
Microprocessor
Socket
a.
Squeeze
and
hold
the
bladder
of
the
tool;
then,
place
the
suction
cup
on
the
microprocessor
and
release
the
bladder.
Note:
To
maintain
proper
orientation
between
the
microprocessor
and
the
microprocessor
socket
during
installation,
observe
the
following
information:
v
The
microprocessor
has
two
notches
that
are
keyed
to
two
tabs
on
the
sides
of
the
socket.
v
A
triangle-shaped
indicator
on
one
corner
of
the
microprocessor
points
to
a
45-degree
angle
on
one
corner
of
the
socket.
b.
Using
the
tool,
carefully
place
the
microprocessor
into
the
socket.
c.
Squeeze
the
bladder
of
the
tool
to
release
the
microprocessor
from
the
suction
cup.
7.
Close
the
microprocessor
bracket
frame;
then,
close
the
microprocessor
retention
latch
and
lock
it
securely
in
place.
8.
Close
the
microprocessor-release
lever
to
secure
the
microprocessor.
9.
Make
sure
that
the
heat-sink
release
lever
is
open.
10.
If
necessary,
remove
the
cover
from
the
bottom
of
the
heat
sink.
11.
Place
the
tab
on
the
heat
sink
into
the
connector
in
the
retention
bracket;
then,
rotate
the
heat
sink
into
place
and
close
the
heat-sink
release
lever.
Note:
If
you
are
installing
an
additional
microprocessor
in
microprocessor
socket
2,
you
must
also
install
a
VRM.
12.
If
necessary,
install
a
VRM
in
the
connector.
Chapter
2.
Installing
optional
devices
41