Intel S1200RP Service Guide - Page 33

Installing and Removing Memory

Get Intel S1200RP PDF manuals and user guides View all Intel S1200RP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Server Utilities Installing Processor Heatsink 1. Remove the Thermal Interface Material (TIM ) if present. 2. Make sure the screwdriver slot at the top of each fastener is rotated perpendicular to the blades of the heatsink as shown (see letter A). Each heatsink has four captive fasteners and should be tightened in a diagonal manner using the following procedure: 1) Align heatsink with holes in board and lower assembly to board. Snaps go through holes in server board (see letter B). 2) Press downward on top of cap (see letter C). 3) Fastener snaps into final position (see letter D). 3. Plug the fan cable into the CPU fan header. Figure 23. Installing Processor Heatsink Installing and Removing Memory Installing Memory 1. Locate the DIMM sockets. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (see letter A). 2. Holding the DIMM by the edges, remove it from its anti-static package. Position the DIMM above the socket. Align the notch on the bottom edge of the DIMM with the key in the DIMM socket (see letter B). 3. Insert the bottom edge of the DIMM into the socket (see letter C). When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place (see letter D). Make sure the clips are firmly in place (see letter E). 20 Intel® Server System P4000RP Family Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
Server Utilities
20
Intel
®
Server System P4000RP Family Service Guide
Installing Processor Heatsink
1.
Remove the Thermal Interface Material (TIM ) if present.
2.
Make sure the screwdriver slot at the top of each fastener is rotated perpendicular to the blades
of the heatsink as shown (see letter
A
).
Each heatsink has four captive fasteners and should be tightened in a diagonal manner using the
following procedure:
1)
Align heatsink with holes in board and lower assembly to board. Snaps go through holes in
server board (see letter
B
).
2)
Press downward on top of cap (see letter
C
).
3)
Fastener snaps into final position (see letter
D
).
3.
Plug the fan cable into the CPU fan header.
Figure 23. Installing Processor Heatsink
Installing and Removing Memory
Installing Memory
1.
Locate the DIMM sockets. Make sure the clips at either end of the DIMM socket(s) are pushed
outward to the open position (see letter
A
).
2.
Holding the DIMM by the edges, remove it from its anti-static package. Position the DIMM
above the socket. Align the notch on the bottom edge of the DIMM with the key in the DIMM
socket (see letter
B
).
3.
Insert the bottom edge of the DIMM into the socket (see letter
C
). When the DIMM is inserted,
push down on the top edge of the DIMM until the retaining clips snap into place (see letter
D
).
Make sure the clips are firmly in place (see letter
E
).