JVC GR-DVM70U Instruction Manual - Page 25

To Record An Image With A Title/Frame .., To Remove The Shutter Sound .., PHOTO SNAPSHOT - cable

Page 25 highlights

PIN-UP Pin-Up mode* FRAME Snapshot mode with frame* FULL Snapshot mode with no frame* MULTI-4 Multi-Analyzer 4 EN25 To Record An Image With A Title/Frame . . . .... refer to "Superimposing A Title/Frame" (੬ pg. 69). To Remove The Shutter Sound . . . .... when you don't want to hear the shutter sound, set BEEP/TALLY to "OFF" in the System Menu (੬ pg. 36 - 39). The sound is no longer hard from the speaker. NOTES: ● Even if "MULTI-4" or "MULTI-9" is engaged, Snapshot recording will be performed in the FULL mode during Digital Zoom. However, the flash will not fire. ● If Snapshot recording is not possible, "PHOTO" blinks when PHOTO (SNAPSHOT) is pressed. ● Even if Program AE with special effects (੬ pg. 44, 45) is engaged, certain modes of Program AE with special effects are disabled during Snapshot recording. In such a case, the icon blinks. ● If shooting is not performed for approx. 5 minutes when the Power Switch is set to " " and power is supplied from the battery pack, the camcorder shuts off automatically to save power. To perform shooting again, close the LCD monitor and re-open it. When using the viewfinder, push back it in and pull it out again. ● Motor Drive Mode (੬ pg. 32) is disabled when the Power Switch is set to " ". ● To reduce the Red-Eye effect of the subject's eyes when the flash fires, ੬ pg. 34. ● When a cable or headphone set is connected to the AV OUT connector, the shutter sound is not heard from the speaker. MULTI-9 Multi-Analyzer 9 *:There is the sound of a shutter closing.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112

EN
25
To Record An Image With A Title/Frame . . .
....
refer to “Superimposing A Title/Frame” (
Z
pg. 69).
To Remove The Shutter Sound . . .
....
when you don’t want to hear the shutter sound, set
BEEP/TALLY to “OFF” in the System Menu
(
Z
pg. 36 – 39). The sound is no longer hard from the
speaker.
NOTES:
Even if “MULTI-4” or “MULTI-9” is engaged, Snapshot
recording will be performed in the FULL mode during
Digital Zoom. However, the flash will not fire.
If Snapshot recording is not possible, “PHOTO” blinks
when
PHOTO (SNAPSHOT)
is pressed.
Even if Program AE with special effects (
Z
pg. 44, 45) is
engaged, certain modes of Program AE with special
effects are disabled during Snapshot recording. In such a
case, the icon blinks.
If shooting is not performed for approx. 5 minutes when
the Power Switch is set to “
” and power is supplied
from the battery pack, the camcorder shuts off automati-
cally to save power. To perform shooting again, close the
LCD monitor and re-open it. When using the viewfinder,
push back it in and pull it out again.
Motor Drive Mode (
Z
pg. 32) is disabled when the
Power Switch is set to “
”.
To reduce the Red-Eye effect of the subject’s eyes when
the flash fires,
Z
pg. 34.
When a cable or headphone set is connected to the AV
OUT connector, the shutter sound is not heard from the
speaker.
FRAME
Snapshot mode
with frame*
FULL
Snapshot mode
with no frame*
PIN-UP
Pin-Up mode*
MULTI-4
Multi-Analyzer 4
MULTI-9
Multi-Analyzer 9
*
:There is the sound of a shutter closing.