Konica Minolta Kodak Scan Station 710 Operation Guide - Page 121

Cleaning the imaging area, Running a transport cleaning sheet

Get Konica Minolta Kodak Scan Station 710 PDF manuals and user guides View all Konica Minolta Kodak Scan Station 710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Cleaning the imaging area 1. Wipe the upper and lower imaging area using a Staticide wipe. Be careful not to scratch the imaging area when cleaning. IMPORTANT: Staticide wipes contain isopropanol which can cause eye irritation and dry skin. Wash your hands with soap and water after performing maintenance procedures. Refer to the MSDS for more information. Running a transport cleaning sheet 2. Wipe the upper and lower imaging area again using the reusable optics cleaner pad to remove any streaks. 3. When finished, close the Scan Station cover with both hands. 1. Remove the wrapping from the Transport Cleaning Sheet. 2. Adjust the side guides to fit the cleaning sheet. 3. Place a transport cleaning sheet in the input tray (adhesive side facing you) in portrait orientation. 4. Select any job or select a destination and touch the green Scan button. 5. After the transport cleaning sheet is scanned, turn it over (adhesive side facing the input tray) and scan it again. 6. Open the Scan Station cover and wipe the imaging area with a lint- free cloth. 7. Close the Scan Station cover with both hands. 8. Check your image quality. 9. If necessary, repeat this procedure until all residue is removed from the rollers. NOTE: When a transport cleaning sheet gets very dirty, discard it and use a new one. 10-6 A-61796 September 2014

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
10-6
A-61796
September
2014
Cleaning the imaging area
1.
Wipe the upper and lower imaging area using a Staticide wipe. Be
careful not to scratch the imaging area when cleaning.
IMPORTANT: Staticide wipes contain isopropanol which can cause eye
irritation and dry skin. Wash your hands with soap and
water after performing maintenance procedures. Refer to
the MSDS for more information.
2.
Wipe the upper and lower imaging area again using the reusable
optics cleaner pad to remove any streaks.
3.
When finished, close the Scan Station cover with both hands.
Running a transport
cleaning sheet
1.
Remove the wrapping from the Transport Cleaning Sheet.
2.
Adjust the side guides to fit the cleaning sheet.
3.
Place a transport cleaning sheet in the input tray (adhesive side
facing you) in portrait orientation.
4.
Select any job or select a destination and touch the green Scan
button.
5.
After the transport cleaning sheet is scanned, turn it over (adhesive
side facing the input tray) and scan it again.
6.
Open the Scan Station cover and wipe the imaging area with a lint-
free cloth.
7.
Close the Scan Station cover with both hands.
8.
Check your image quality.
9.
If necessary, repeat this procedure until all residue is removed from
the rollers.
NOTE: When a transport cleaning sheet gets very dirty, discard it and
use a new one.