Konica Minolta Kodak Scan Station 710 Operation Guide - Page 124

Replacing the pre-separation pad, separation module.

Get Konica Minolta Kodak Scan Station 710 PDF manuals and user guides View all Konica Minolta Kodak Scan Station 710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Replacing the preseparation pad 1. Remove the separation module from the Scan Station by following the steps previously described in "Replacing the separation module and tires". 2. Hold the separation module in both hands and locate the two tabs which protrude slightly from the back of the separation module. 3. Push down on the tabs until the pre-separation pad protrudes slightly from the front of the separation module. 4. Grasp the pre-separation pad and pull it out of the separation module. 5. Discard the worn pre-separation pad. 6. Align the side tabs of a new pre-separation pad with the slots on the separation module. 7. Push the pre-separation pad firmly in the slots until the preseparation pad flap rests lightly against the separation module tires. 8. Reinstall the separation module by aligning the tabs with the slots and snapping it into position. A-61796 September 2014 10-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
A-61796
September 2014
10-9
Replacing the pre-
separation pad
1.
Remove the separation module from the Scan Station by following
the steps previously described in “Replacing the separation module
and tires”.
2.
Hold the separation module in both hands and locate the two tabs
which protrude slightly from the back of the separation module.
3.
Push down on the tabs until the pre-separation pad protrudes
slightly from the front of the separation module.
4.
Grasp the pre-separation pad and pull it out of the separation
module.
5.
Discard the worn pre-separation pad.
6.
Align the side tabs of a new pre-separation pad with the slots on the
separation module.
7.
Push the pre-separation pad firmly in the slots until the pre-
separation pad flap rests lightly against the separation module tires.
8.
Reinstall the separation module by aligning the tabs with the slots
and snapping it into position.