Kyocera C8100DN Command Center Guide - Page 11

Basic Basic > Defaults > Network - + manual

Get Kyocera C8100DN - Color Laser Printer PDF manuals and user guides View all Kyocera C8100DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

COMMAND CENTER Pages Item Description Kyocera Online http://www.kyoceramita.com/ Basic Page This section includes settings that apply to the machine, such as Device Defaults, Security, and basic Networking. If the Admin password has been set, pages in this section are available only to the Administrator. Basic > Defaults > Network This page allows you to make the settings that are required for network printing and sending E-mail. For more information, refer to Advanced > Protocols > TCP/IP > General on page 35. You must restart this machine after you have completed these settings in order to properly register the content of those settings in the machine. Refer to Basic > Defaults > Reset on page 9. Item Description Host Name LAN Interface Specifies a name for the printing system network component. This name is used as the NetBEUI printer name and as the WSD device name. Specifies the communication rate from Auto, 10BASE-T-Half, 10BASE-T-Full, 100BASE-TX-Half, and 100BASE-TX-Full. After you have changed this setting, you must restart this machine. For the restarting procedure, refer to Basic > Defaults > Reset on page 9. IPv4 Settings DHCP/ BOOTP Specifies whether or not to obtain an IP address using DHCP or BOOTP. IP Address Assigns the Internet Protocol address on the printing system (IPv4) network component. Format of the IP address is four-byte (32-bit) numbers separated by dots, e.g. 192.168.110.171. Subnet Mask Specifies the subnet mask of the hosts or network with which the print system is connecting. If you have manually assigned an IP address that starts with a number between 192 and 223, it is recommended that you set the subnet mask to "255.255.255.0." Default Gateway Specifies the IP address of the default gateway. IPv6 Settings IPv6 IP Address (IPv6) Specifies whether or not to enable the IPv6 protocol. Select On to use the IPv6 protocol. Assigns an IPv6 address to the printing system network component. The format of the IPv6 address is a sequence of numbers (128 bit in total) separated by colons, e.g. 2001:db8:3c4d:15::1a2c:1a1f. Operation Guide 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
COMMAND CENTER Pages
Operation Guide
7
Basic Page
This section includes settings that apply to the machine, such as Device Defaults,
Security, and basic Networking. If the Admin password has been set, pages in this
section are available only to the Administrator.
Basic > Defaults > Network
This page allows you to make the settings that are required for network printing and
sending E-mail. For more information, refer to
Advanced > Protocols > TCP/IP >
General
on page 35.
You must restart this machine after you have completed these settings in order to
properly register the content of those settings in the machine. Refer to
Basic > Defaults
> Reset
on page 9.
Kyocera Online
Item
Description
Item
Description
Host Name
Specifies a name for the printing system network
component. This name is used as the NetBEUI printer name
and as the WSD device name.
LAN Interface
Specifies the communication rate from
Auto
,
10BASE-T-Half
,
10BASE-T-Full
,
100BASE-TX-Half
, and
100BASE-TX-Full
.
After you have changed this setting, you must restart this
machine. For the restarting procedure, refer to
Basic >
Defaults > Reset
on page 9.
IPv4 Settings
DHCP/
BOOTP
Specifies whether or not to obtain an IP address using
DHCP or BOOTP.
IP Address
(IPv4)
Assigns the Internet Protocol address on the printing system
network component. Format of the IP address is four-byte
(32-bit) numbers separated by dots, e.g.
192.168.110.171
.
Subnet
Mask
Specifies the subnet mask of the hosts or network with which
the print system is connecting. If you have manually
assigned an IP address that starts with a number between
192 and 223, it is recommended that you set the subnet
mask to "255.255.255.0."
Default
Gateway
Specifies the IP address of the default gateway.
IPv6 Settings
IPv6
Specifies whether or not to enable the IPv6 protocol.
Select
On
to use the IPv6 protocol.
IP
Address
(IPv6)
Assigns an IPv6 address to the printing system network
component. The format of the IPv6 address is a sequence of
numbers (128 bit in total) separated by colons, e.g.
2001:db8:3c4d:15::1a2c:1a1f.