Lexmark Forms Printer 2400 Service Manual - Page 100

While holding the lower pinch roller shaft by the gear

Get Lexmark Forms Printer 2400 PDF manuals and user guides View all Lexmark Forms Printer 2400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

24xx 9. Unhook the spring clip [A] from the left end of the lower pinch roller shaft and push it off the gray slotted spring block [B] toward the back of the printer, as shown. 10. Slide the carrier to the center of the printer. 11. Slide the gray slotted spring blocks [B], on each end, toward the center of the roller shaft, taking care that the blocks remain with the shaft during removal. 12. Slide the carrier to the right side of the printer. 13. While holding the lower pinch roller shaft by the gear [C], move the shaft to the left approximately one half inch. Lift the shaft up and to the back of the printer and carefully remove the lower pinch roller and shaft. 14. Be sure to perform the Printhead-to-Platen Gap Adjustment procedure. Go to "Printhead-to-Platen Gap Adjustment" on page 4-2. 4-40 Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
4-40
Service Manual
24xx
9.
Unhook the spring clip [
A
] from the left end of the lower pinch
roller shaft and push it off the gray slotted spring block [
B
]
toward the back of the printer, as shown.
10.
Slide the carrier to the center of the printer.
11.
Slide the gray slotted spring blocks [
B
], on each end, toward the
center of the roller shaft, taking care that the blocks remain with
the shaft during removal.
12.
Slide the carrier to the right side of the printer.
13.
While holding the lower pinch roller shaft by the gear [
C
], move
the shaft to the left approximately one half inch. Lift the shaft up
and to the back of the printer and carefully remove the lower
pinch roller and shaft.
14.
Be sure to perform the Printhead-to-Platen Gap Adjustment
procedure. Go to
“Printhead-to-Platen Gap Adjustment” on
page 4-2
.