Netgear WG302v2 WG302v2 Reference Manual

Netgear WG302v2 - ProSafe 802.11g Wireless Access Point Manual

Get Netgear WG302v2 - ProSafe 802.11g Wireless Access Point PDF manuals and user guides View all Netgear WG302v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Netgear WG302v2 manual content summary:

  • Netgear WG302v2 | WG302v2 Reference Manual - Page 1
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10146-01 May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 2
    void the user's authority to operate the equipment. NETGEAR does not assume any liability that may occur due to such condition. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice ProSafe 802.11g Wireless Access Point WG302v2 Tested to Comply with FCC Standards FOR HOME
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 3
    FCC Statement Declaration of Conformity We NETGEAR, 4500 Great America Parkway Santa Clara, CA 95054, USA Tel: +1 408 907 8000 declare under our sole responsibility that the product(s) WG302v2 (Model Designation) ProSafe™ 802.11g Wireless Access Point (Product Name) complies with Part 15 of FCC
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 4
    result in significant performance degradation or inability to wirelessly connect to the wireless access point. RF Exposure Warning for North America, and http://kbserver.netgear.com/products/wg302.asp for an updated list of wireless accessories approved to be used with the WG302v2. Industry Canada
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 5
    meets the following conformance standards: EN300 328, EN301 489-17, EN60950 Europe - Declaration of Conformity in Languages of the European Community Èesky [Czech] NETGEAR Inc. tímto prohlašuje, _e tento Radiolan je ve shodě se základními po_adavky a dalšími příslušnými ustanoveními směrnice 1999
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 6
    li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ követelm of the European Community using the 2.4GHz band: Channels 1 - 13, except where noted below: • In Italy the end-user must apply for a license from the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 7
    8.9 dBm + 9 dBi = 17.9 dBm EIRP 14 dBm + 5 dBi = 19 dBm EIRP a. WG302v2 maximum radiated power in the European Community: 15 dBm - cable loss + antenna gain Please go to http://www.NETGEAR.com and use the search feature to find an updated list of wireless accessories approved to be used with the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 8
    Access Point has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 9
    Equipment Placement and Range Guidelines 2-2 Installing the ProSafe 802.11g Wireless Access Point 2-3 Logging in to the WG302v2 Using Its Default IP Address 2-7 Basic IP Settings ...2-8 Wireless Settings ...2-10 Understanding WG302v2 Wireless Security Options 2-12 Configuring Security Profiles
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 10
    Upgrading the Wireless Access Point Firmware 3-4 Configuration File Management 3-5 Backing up and Restoring the Configuration 3-6 Erasing the Configuration 3-6 Using the Reset Button to Restore Factory Default Settings 3-6 Viewing General Information 3-7 Viewing the Activity Log 3-9 Viewing
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 11
    the LAN with a wireless capable computer 5-2 I cannot connect to the WG302v2 to configure it 5-3 When I enter a URL or IP address I get a timeout error 5-3 I am unable to download files from some FTP sites 5-4 I need to restore factory default settings 5-4 Appendix A Related Documents Appendix
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 12
    xii v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 13
    About This Manual The NETGEAR® ProSafe™ Wireless Access Point 802.11g WG302 Reference Manual describes how to install, configure and troubleshoot the ProSafe 802.11g Wireless Access Point.The information in this manual is intended for readers with intermediate computer and Internet skills.
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 14
    : Product Version Manual Publication Date ProSafe 802.11g Wireless Access Point May 2006 For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, "Related Documents". Note: Product updates are available on the NETGEAR, Inc
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 15
    ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual - Click the PDF of This Chapter link at the top right of any page in the chapter you want to print. The PDF version of the chapter you were viewing opens in a browser window. - Click the print icon in the upper left of the window. Tip
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 16
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual xvi About This Manual v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 17
    servers, and other devices. The wireless access point provides wireless connectivity within about a 300-foot radius. The wireless access point can support up to 40 users simultaneously. The WG302v2 acts as a bridge between the wired LAN and wireless clients. You can connect multiple wireless access
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 18
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • Multiple BSSIDs. Support for multiple BSSIDs. When one AP is connected to a wired network and a set of wireless stations, it is referred to as a Basic Service Set (BSS). The Basic Service Set Identifier (BSSID) is a 32-
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 19
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • Simple Configuration. If the default settings are unsuitable, they are easy to change. • Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct SSID can connect. • Configuration Backup.
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 20
    package should contain the following items: • ProSafe 802.11g Wireless Access Point WG302v2. • Power adapter and cord. • Straight through Category 5 Ethernet cable. • Resource CD for the NETGEAR ProSafe 802.11g Wireless Access Point WG302. • Support Registration card. Contact your reseller or
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 21
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Hardware Description This section describes the WG302v2 front and rear hardware functions. Front Panel Figure 0-1 Viewed from left to right, the WG302v2 has these status LEDs: PWR, TEST, LAN, and 802.11g WLAN. LED Description
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 22
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual LED Description 802. WG302v2: 1. Primary and Secondary 2.4 GHz detachable antennas. 2. Reset button. This restores the default factory settings. 3. Serial Console Port. Use the male DB-9 serial port for serial DTE connections
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 23
    how to set up your ProSafe 802.11g Wireless Access Point WG302v2 for wireless connectivity to your LAN. This basic configuration enables computers with 802.11b/g wireless adapters to do such things as connect to the Internet or access printers and files on your LAN. Note: Indoors, computers can
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 24
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • A Web browser for configuration such as Microsoft Internet Explorer 6.0 or above, or Netscape Navigator 4.78 or above. • At least one computer with the TCP/IP protocol installed. • 802.11g or 802.11b-compliant devices, such as
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 25
    described in "System Requirements" on page 2-1. Note: To view a list of the factory default settings, see "Default Factory Settings" in Appendix B. To set up and install your WG302v2 Wireless Access Point: 1. Set up the WG302v2. Tip: Before mounting the WG302v2 in a high location, first set up and
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 26
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Enter 192.168.0.228 in the address field of your browser. The WG302v2 login screen appears. When prompted, enter admin for the user name, and password for the password, both in lower case letters. For more information, see "
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 27
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual b. Click the Basic Settings link in the Setup section of the main menu to view the Basic Settings menu. Figure 2-2 c. Configure the settings for your network and click Apply. See the online help or "Basic IP Settings" on page 2-8
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 28
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual c. Connect an Ethernet cable from your WG302v2 to a LAN port on your router, switch, or hub. Note: By default, the DHCP client on the WG302v2 is disabled. If your network uses dynamic IP addresses, you must change this setting.
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 29
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Logging in to the WG302v2 Using Its Default IP Address After you install the WG302v2, log in to it to configure the basic settings and the wireless settings. The WG302v2 is set, by default, with the IP address of 192.168.0.228
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 30
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual 4. Log on by using the default user name of admin and default password of password. After you log on, the Web browser displays the General Information page as shown in Figure 2-1 on page 2-4. Basic IP Settings To configure the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 31
    (DHCP) client is disabled. If you have a DHCP server on your LAN and you enable DHCP, the wireless access point get its IP address, subnet mask and default gateway settings automatically from the DHCP server on your network when you connect the WG302v2 to your LAN. Note: To connect to the WG302v2
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 32
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual By default all traffic on the WG302v2 uses VLAN 1, which is the default untagged VLAN. Therefore, all traffic is untagged until you change the untagged traffic VLAN ID or the VLAN ID for a specific Security Profile. Check the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 33
    ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual The Wireless Settings page options are discussed below: • Turn Radio On. On by default, you can also turn off the radio to disable access through this device. This can be helpful for configuration, network tuning, or troubleshooting
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 34
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual - If you use multiple access points, it is better if adjacent access points use different channels to reduce interference. The recommended channel spacing between adjacent access points is five channels (for example, use channels
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 35
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • Use WPA, WPA-PSK, WPA2, or WPA2-PSK. Wi-Fi Protected Access (WPA and WPA2) data encryption provides data security. The very strong authentication along with dynamic per frame rekeying of WPA make it virtually impossible to
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 36
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual 3. Select the Security Profile to configure and click Security Profile, which are described on the following page. 5. To update the settings, click Apply. Note: If you use a wireless computer to configure Security Profile settings
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 37
    , note the following information: • If you are using Access Point mode, then all options are available. In other modes such as Repeater or Bridge, some options might be unavailable. • Not all wireless adapters support WPA or WPA2. Windows XP and Windows 2000 with Service Pack 3 do include the client
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 38
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual version of WPA. Only select this if all clients support WPA2. If selected, you must use AES encryption and configure the RADIUS Server Settings. WPA and WPA2 with This selection allows clients (otherwise, the default is None). The
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 39
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table 2-2 Data Encryption Settings (continued) Settings AES TKIP + AES Description This is the standard encryption method for WPA2. Some clients may support AES with WPA, but this is not supported by this Access Point. This
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 40
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual The VLAN assigned to the first Security Profile (default name: NETGEAR) is the management VLAN. By default all traffic on the WG302v2 uses VLAN 1, which is the default untagged VLAN. Therefore, all traffic is untagged until you
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 41
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual SSID and Service Set Identification (SSID) identifies the wireless local area network. You may customize it by using up to 32 alphanumeric characters. Write your SSID on the line. SSID Note: The SSID in the wireless access point
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 42
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Configuring the RADIUS Server Settings To view or change the RADIUS Server Settings: 1. Connect to the WG302v2. 2. In the address field of your Web browser, enter the default LAN address of http://192.168.0.228. Log in with the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 43
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual The following list describes the RADIUS Server Settings: • Authentication Server Configuration. This configuration is required for authentication and access control using a RADIUS Server.The IP Address, Port Number and Shared
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 44
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Figure 2-9 3. Select the Turn Access Control On check box. Note: When configuring the WG302v2 from a wireless computer whose MAC address is not in the access control list, if you select Turn Access Control On, you will lose your
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 45
    information features of your ProSafe 802.11g Wireless Access Point. To get to these features, connect to the WG302v2 as described in "Logging in to the WG302v2 Using Its Default IP Address" on page 2-7. Changing the Administrator Password The default password is password. NETGEAR recommends that you
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 46
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Remote Management To access the Remote Management screen: 1. Enter the LAN address of the WG302v2 into the address field of your browser. 2. After you log in, click Remote Management under Management on the main menu . Figure
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 47
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Using the Secure Telnet Interface The WG302v2 includes a secure Telnet command line interface (CLI). You can access the CLI from a secure Telnet client over the Ethernet port or over the serial console port. Note: You must use a
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 48
    are explained in Appendix C, "Command Line Reference". Upgrading the Wireless Access Point Firmware The ProSafe 802.11g firmware is stored in FLASH memory and can be upgraded as new firmware is released by NETGEAR. You can download the upgrade files from the NETGEAR Web site. You can upload the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 49
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual 3. From the main menu Management section, click the Upgrade Firmware link. 4. In the Upgrade Firmware menu, click the Browse button and browse to the location of the image (.tar) upgrade file. 5. Click Upload. When the upload
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 50
    NETGEAR, the DHCP client will be disabled, the default LAN IP address will be 192.168.0.228, and the access point name is reset to the name printed on the label on the bottom of the unit. Using the Reset Button to Restore Factory Default Settings If you do not know the login password or IP address
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 51
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Viewing General Information The information on the General screen is a summary of the WG302v2 configuration settings. From the WG302v2 main menu, click General to view the screen shown below. Figure 3-5 Management and
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 52
    Point, Point-to-point bridge, Multi-point bridge or Repeater. Indicates if VLAN support is enabled. The default is enabled. The IP address of the wireless access point. The subnet mask for the wireless access point. The default gateway for the wireless access point communication. If the DHCP Client
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 53
    Wireless Access Point WG302v2 Reference Manual Viewing the Activity Log To access the Activity Log, connect to the WG302v2 and click Activity Log under the Information heading. Figure 3-6 The Activity Log Window displays the Access Point system activity. You can click Refresh to update the display
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 54
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Viewing the Available Wireless Station List The Available Wireless Station List contains a table of all IP devices associated with the wireless access point for the Wired Network Name (SSID) From the WG302v2 main menu, under the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 55
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Viewing Statistics The Statistics screen provides LAN and WLAN statistics. From the WG302v2 main menu, click Statistics under the Information heading to view the screen shown in Figure 3-8. Figure 3-8 Table 3-2 explains the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 56
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table 3-2 Access Point Statistics Field Wireless Interface Unicast Packets Broadcast Packets Multicast Packets Total Packets Total Bytes Refresh button Description Received/Transmitted The Unicast packets sent since the
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 57
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Figure 3-9 To import a list of known APs, use the following steps: 1. Create a text file that contains the MAC address of each known AP, separated by a
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 58
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual 3. Click Browse and navigate to the location where you saved the text file. 4. Select the file and click Open. 5. Click Import to upload the list to the AP. 3-14 v1.0, May 2006 Management and Information
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 59
    : • IP Settings: Use the AP as a DHCP server for wireless clients. • Hotspot Settings: Capture and redirect all HTTP (TCP, port 80) requests. • Wireless Settings: Configure advanced wireless LAN parameters and Quality of Service (QoS). • Access Point Settings: Enable wireless bridging and repeating
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 60
    the pre-configured TCP/IP configurations for wireless clients connected to this wireless access point. The default setting is disable. Note: The DHCP server only assigns network information to clients that connect to the WG302v2 through Security Profiles that are on the same VLAN as Security Profile
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 61
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • Lease: Enter a lease time in days, hours and minutes. The wireless client must renew the IP address when the lease expires. The default lease time is one day. Configuring Hotspot Settings If you want the wireless access point
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 62
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Configuring Wireless LAN Parameters Figure 4-3 shows the Advanced Wireless Settings screen that includes both the Wireless LAN Parameters section and the QoS Queue Parameters section. For most networks, the default Advanced
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 63
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table 4-1 describes the Advanced Wireless Parameters. Table 4-1 Advanced Wireless LAN Parameters Field Enable SuperG Mode traffic. For WMM to function correctly, wireless clients must also support WMM. If WMM is disabled, you
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 64
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual different types of data transmitted from the WG302v2 to the wireless client. • Modify Station EDCA Parameters. priority queue, medium throughput and delay. Most traditional IP data is sent to this queue. Lowest priority queue
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 65
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Wireless Bridging and Repeating The ProSafe 802.11g lets you build large bridged wireless networks. Examples of wireless bridged configurations are: • Point-to-Point Bridge. The WG302v2 communicates with another bridge-mode
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 66
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Figure 4-4 4-8 Advanced Configuration v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 67
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Point-to-Point Bridge Configuration In Point-to-Point Bridge mode, the WG302v2 communicates with another bridge-mode wireless station. In addition, you can enable client associations with this WG302v2. You must enter the MAC
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 68
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Multi-Point Bridge Configuration Multi-point bridge mode allows a wireless access point to bridge to multiple peer wireless access points simultaneously. In addition, you can enable client associations with this WG302v2. Multi-
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 69
    segment. Note: You can extend this multi-point bridging by adding additional WG302v2s configured in Point-to-Point mode for each additional LAN segment. Furthermore, you can extend the range of the wireless network with NETGEAR wireless antenna accessories. Repeater with Wireless Client Association
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 70
    Wireless Access Point WG302v2 Reference Manual • You do not have the option of disabling client associations with this WG302v2. • You cannot configure a sequence of parent/child APs. You are limited to only one parent/child AP pair. The figure below shows an example of a Repeater Mode configuration
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 71
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual • All ProSafe 802.11g devices use the same SSID, Channel, authentication mode, if any, and encryption in use. 3. Verify connectivity across the LANs. A computer on any LAN segment should be able to connect to the Internet or
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 72
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual 4-14 v1.0, May 2006 Advanced Configuration
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 73
    I connected the wireless access point correctly? Go to "Installing the ProSafe 802.11g Wireless Access Point" on page 2-3. • I cannot remember the wireless access point's configuration password. Go to "Viewing the Activity Log" on page 3-9. If you have trouble setting up your WG302v2, check the tips
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 74
    setting for Windows the Network Properties is set to "Obtain an IP address automatically." • The access point's default values may not work with your network. Check the access point default configuration against the configuration of other devices in your network. 5-2 Troubleshooting v1.0, May
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 75
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual I cannot connect to the WG302v2 to configure it. Check these items: • The WG302v2 is properly installed, LAN connections are OK, and it is powered on. Check that the LAN port LED is on (amber indicating a 10 Mbps Ethernet
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 76
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual I am unable to download files from some FTP sites. If the IP address of the WG302v2 LAN interface is not on the same network as the IP addresses the DHCP server on the WG302v2 assigns to wireless clients, the WG302v2 performs
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 77
    Networking and TCP/IP http://documentation.netgear.com/reference/enu/tcpip/index.htm Addressing: Wireless Communications: http://documentation.netgear.com/reference/enu/wireless/index.htm Preparing a Computer for Network Access: http://documentation.netgear.com/reference/enu/wsdhcp/index
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 78
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual A-2 Related Documents v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 79
    B-1 Access Point Default Configuration Settings Feature AP Login User Login URL User Name (case sensitive) Login Password (case sensitive) Ethernet Connection Ethernet MAC Address Port Speed Basic Settings AP Name Country / Region IP Address Subnet Mask DHCP Client Spanning Tree Protocol VLAN (802
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 80
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table B-1 Access Point Default Configuration Settings Feature Description Untagged Packet and VLAN Mapping Untagged VLAN ID Time Zone Time Zone Adjusted for Daylight Saving Time Wireless Settings Wireless Communication (Radio
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 81
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table B-1 Access Point Default Configuration Settings Feature Description Remote Management SSH Enabled SNMP Public Community Name Enabled public Private Community Name private Community Name for Traps IP Address to
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 82
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Specifications for the WG302v2 The following table describes the WG302v2 technical specifications. Table B-2 WG302v2 Technical Specifications Parameter ProSafe 802.11g Wireless Access Point Network Management Web-based
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 83
    # add config factory-reset firmware-upgrade get reboot Add an instance to the running configuration Upload/Download the running configuration Reset the system to factory defaults Upgrade the firmware Get property values of the running configuration Reboot the system Command Line Reference C-1 v1
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 84
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual remove save-running set Remove instances in the basic-rate bridge-port .... vap web-server wme-queue Associated station Basic rates of radios Bridge ports of bridge interfaces Virtual Access Point Web server Transmission queue
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 85
    internal interface for the access point. To Telnet or SSH into the access point, use the IP address for this interface. The brvlan1 interface consists of: • eth0 (or vlan if you have VLANs configured) • wlan0 • Internal bridge trunk interface. Command Line Reference C-3 v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 86
    existing instance of a class. Uploads or downloads the running configuration. Upgrades the firmware. Saves the running configuration as the startup configuration. Restarts the access point (a "soft" reboot). Resets the AP to factory defaults and reboots. C-4 Command Line Reference v1.0, May 2006
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 87
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Warning: Settings updated from the CLI (with get, set, pairs. You can use CLI commands to view or configure most of the features that you can view and configure by using the Web UI. Note: CLI commands are not available to merge,
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 88
    Access Point View the Access Point Mode get system version get interface brvlan1 type View the Untagged VLAN ID get untagged-vlan Current IP Settings View the IP Address get interface brvlan1 View the Subnet Mask get interface brvlan1 View the Default Gateway IP address View the DHCP Client
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 89
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual helpful for viewing basic system information. Table C-5 System Information Task View hardware information View information about all interfaces View information about the 802.11 radio View information about the Security
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 90
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-6 Basic Setting (continued)s Task Command Set the Primary DNS Server set host static-dns-1 Example: set host static-dns-1 10.10.3.10 Set the Secondary DNS Server set host static-dns-2
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 91
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-7 Wireless Setting (continued)s Task Configure the Wireless Network Name (SSID) Allow SSID Broadcasts Deny SSID Broadcasts Set the Wireless Mode Set the Channel/Frequency Set the Data Rate Set the Output Power Command
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 92
    ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual The commands in Table C-9 correspond to the Security Profile Settings page on the Web UI. The commands in this table show how to configure Security Profile 1, which is the default profile and has a default profile name of NETGEAR. Note
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 93
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-9 Security Profile Settings (continued) Task Set the WEP Keys Command set interface wlan0 wep-key-1 Note: For 64-bit WEP, use 5 ASCII characters or 10 Hex characters. For 128-bit WEP, use 13 ASCII characters or
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 94
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-9 Security Profile Settings (continued) Task Client Security set radio wlan0 station-isolation off Separation Set the VLAN ID for the Security set vap vap0 with radio wlan0 vlan-id Profile RADIUS Server
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 95
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-10 RADIUS Server Settings (continued) Task Command Set the Port Number of the Pri- set radius-client mary Accounting Server primary-accounting-port Set the Shared Secret for the Primary Accounting
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 96
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Viewing and Configuring Management Settings The commands in Table C-12 correspond to the pages on the Web UI under the Management heading. This section includes commands for the following features: • Change Password • Remote
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 97
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Viewing and Configuring System Information The in the SysLog server set log relay-port View a list of wireless stations get association detail View interface statistics get interface all ip mac ssid tx-
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 98
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-13 AP Information (continued) Task Save the list of Known APs Import a list of known APs Command set known-ap-list action export config-file config-server Example: set known-ap-list action
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 99
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-14 Advanced IP Setting (continued)s Task Set the Secondary DNS Server Set the Primary WINS Server Set the Secondary WINS Server Set the Lease Command set dhcp-server dns2 set dhcp-server wins1
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 100
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Table C-16 Advanced Wireless Settings (continued) Task Command Set the DTIM Interval Enable Wi-Fi Multimedia (WMM) Disable Wi-Fi Multimedia (WMM) set bss wlan0bssvap0
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 101
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual Advanced Access Point Settings The commands in Table C-17 correspond to the Access Point Settings page on the Web UI under the Advanced heading. Table C-17 Advanced Access Point Settings Task Command Enable Wireless Bridging
  • Netgear WG302v2 | WG302v2 Reference Manual - Page 102
    NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual C-20 v1.0, May 2006 Command Line Reference
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
202-10146-01
May 2006
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
NETGEAR ProSafe
802.11g Wireless Access
Point WG302v2
Reference Manual