Oki GL408e GL408e/GL412e User's Guide - Page 45

Centronics Interface Mode,

Get Oki GL408e PDF manuals and user guides View all Oki GL408e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Unit 4: Printer Configuration CENTRONICS INTERFACE MODE This chapter provides the programming sequences required for Centronics interface setup. Use the keys of the printer's operator panel to select and enter the required options. Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen. ATTENTION: Perform the following programming sequence only if this is the interface type to be used. Instead, refer to the appropriate interface programming chart. POWER ONLINE LINE OFFLINE FUNCTION INTERFACES Interface Mode ENTER INTERFACES Ignore CR/LF Item No. Check BCC Check History Buffer Comm. Protocol Host Interface Parallel Port USB Port Serial Port Printer Mgmt Screens only display if Admin User is enabled within the Advanced Mode ENTER Timeout 10 sec.* Report Status Disable* Prime Signal Disable* Data Polarity Standard* Response Polarity Standard* Busy on Strobe Enable* Latch Data On 10 sec* Offline Process Disable* Ignore CR/LF No* Item No. Check Disable* BCC Check Disable* History Buffer Temporary* Comm. Protocol Status 5* Host Interface Auto Switching* Parallel Port Port Type Port Type Centronics Data Bit 8 Enable* PI Ignored Enable* Buffer Size in K 16* Auto Trickle Disable* Trickle Time 1/4 sec* Host Interface Centronics Parallel Port Port Type CENTRONICS Data Bit 8 Data Bit 8 Enable* PI Ignored Enable* Data Polarity Standard* Resp. Polarity Standard* Busy on Strobe Enable* Latch Data On Leading* Prime Signal Disable* TOF Action Reset* Buffer Size in K 16* Figure 4-6, Centronics Interface Mode GL408-412e Operator Manual 4-9 PN: 9001163A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Unit 4:
Printer Configuration
GL408-412e Operator Manual
4-9
PN: 9001163A
CENTRONICS INTERFACE MODE
This chapter provides the programming sequences required for Centronics interface setup. Use the keys of the
printer’s operator panel to select and enter the required options.
Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen.
Figure 4-6, Centronics Interface Mode
ATTENTION:
Perform the following programming sequence only if this is the interface
type to be used. Instead, refer to the appropriate interface programming chart.
Timeout
10 sec.*
Prime Signal
Disable*
Offline Process
Disable*
PI Ignored
Enable*
Data Bit 8
Enable*
INTERFACES
INTERFACES
Ignore CR/LF
Item No. Check
BCC Check
History Buffer
Comm. Protocol
Host Interface
Parallel Port
USB Port
Serial Port
Printer Mgmt
POWER
ONLINE
OFFLINE
LINE
FUNCTION
Interface
Mode
ENTER
Buffer Size in K
16*
Auto Trickle
Disable*
Trickle Time
1/4 sec*
Report Status
Disable*
Ignore CR/LF
No*
Host Interface
Centronics
Parallel Port
Port Type
CENTRONICS
Data Bit 8
Item No. Check
Disable*
BCC Check
Disable*
History Buffer
Temporary*
Comm. Protocol
Status 5*
Host Interface
Auto Switching*
Data Bit 8
Enable*
PI Ignored
Enable*
Data Polarity
Standard*
Data Polarity
Standard*
Response Polarity
Standard*
Busy on Strobe
Enable*
Latch Data On
10 sec*
ENTER
Parallel Port
Port Type
Port Type
Centronics
Screens
only display if
Admin User is
enabled within
the Advanced
Mode
Resp. Polarity
Standard*
Busy on Strobe
Enable*
Latch Data On
Leading*
Prime Signal
Disable*
TOF Action
Reset*
Buffer Size in K
16*