Sharp NP-PH3501QL Installation Manual - NEC - Page 55

Connecting the cable, Attach the sleeves after tightening the screw.

Get Sharp NP-PH3501QL PDF manuals and user guides View all Sharp NP-PH3501QL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

1. Before Setting Up Your Projector Connecting the cable In order to attach the power cable to the connector block, connect the wires using the following procedure such that the individual wires cannot directly touch each other. 1. Remove the power cable sleeves from the terminals to ensure that the sleeves are not pinched by the terminal attachment screw. Pull back the sleeves from the terminal area before fastening the screw to prevent the sleeves from being pinched. Sleeves 2. Attach the sleeves after tightening the screw. Tighten the fixing screw to the designated torque. Use sleeves and secure the insulation to ensure that terminals do not touch each other. If the cables are attached to the power supply terminal without using sleeves, there is a risk of the terminals touching each other as shown in the photograph on the right. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
29
1. Before Setting Up Your Projector
Connecting the cable
In order to attach the power cable to the connector block, connect the wires using the following procedure such that
the individual wires cannot directly touch each other.
1. Remove the power cable sleeves from the terminals to
ensure that the sleeves are not pinched by the terminal
attachment screw.
Pull back the sleeves from the terminal area before fastening
the screw to prevent the sleeves from being pinched.
Sleeves
2. Attach the sleeves after tightening the screw.
Tighten the fixing screw to the designated torque.
Use sleeves and secure the insulation to ensure that terminals
do not touch each other. If the cables are attached to the
power supply terminal without using sleeves, there is a risk of
the terminals touching each other as shown in the photograph
on the right.