Sony DAV IS50 Operating Instructions - Page 26

To quit the Quick Setup, Press, to select [YES]., Unplug the calibration microphone - test

Get Sony DAV IS50 - Bravia Theater Home System PDF manuals and user guides
UPC - 027242730953
View all Sony DAV IS50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Getting Started Note • The ECM-AC2 jack is used for the supplied calibration microphone only. Do not connect other microphones. Rear of the control unit DMPORT To ECM-AC2 jack Calibration microphone 10 Press C/c to select [YES]. Note • Make sure that the headphones are not connected to the surround amplifier (not supplied, page 63). You cannot operate following steps with the headphones connected. 11 Press . [AUTO CALIBRATION] starts. Be quiet during the measurement. Note • Loud test sound is output when [AUTO CALIBRATION] starts. You cannot turn the volume down. Give consideration to children and neighbors. • Avoid being in the measurement area and making noise during the measurement (which takes about 1 minute), as it may interfere with measurement. 12 Unplug the calibration microphone and press C/c to select [YES]. Note • The environment of the room in which the system is installed may affect measurements. • If measurement fails, follow the message then retry [AUTO CALIBRATION]. 13 Press . Quick Setup is finished. All connections and setup operations are complete. To quit the Quick Setup Press DISPLAY in any Step. Tip • If you cancel [AUTO CALIBRATION], perform the speaker settings in "Settings for the Speakers" (page 85). • If you change the position of the speakers, reset the speaker settings. See "Calibrating the Appropriate Settings Automatically" (page 77). • If you want to change any of the settings, see "Using the Setup Display" (page 79). • For details on [AUTO CALIBRATION] and the error messages of [AUTO CALIBRATION], see "Calibrating the Appropriate Settings Automatically" (page 77). 26US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
26
US
Getting Started
Note
• The ECM-AC2 jack is used for the supplied
calibration microphone only. Do not connect
other microphones.
10
Press
C
/
c
to select [YES].
Note
• Make sure that the headphones are not
connected to the surround amplifier (not
supplied, page 63). You cannot operate
following steps with the headphones connected.
11
Press
.
[AUTO CALIBRATION] starts. Be quiet
during the measurement.
Note
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the
volume down. Give consideration to children
and neighbors.
• Avoid being in the measurement area and
making noise during the measurement (which
takes about 1 minute), as it may interfere with
measurement.
12
Unplug the calibration microphone and
press
C
/
c
to select [YES].
Note
• The environment of the room in which the
system is installed may affect measurements.
• If measurement fails, follow the message then
retry [AUTO CALIBRATION].
13
Press
.
Quick Setup is finished. All connections
and setup operations are complete.
To quit the Quick Setup
Press
DISPLAY in any Step.
Tip
• If you cancel [AUTO CALIBRATION], perform the
speaker settings in “Settings for the Speakers”
(page 85).
• If you change the position of the speakers, reset the
speaker settings. See “Calibrating the Appropriate
Settings Automatically” (page 77).
• If you want to change any of the settings, see “Using
the Setup Display” (page 79).
• For details on [AUTO CALIBRATION] and the error
messages of [AUTO CALIBRATION], see
“Calibrating the Appropriate Settings Automatically”
(page 77).
DMPOR
T
Calibration microphone
Rear of the control unit
To ECM-AC2 jack