Sony ICD-TX50 Operating Instructions - Page 9

Index, Table of, Contents, Preparing the Recorder

Page 9 highlights

Table of Contents Index  Preparing the Recorder Rear Attaching the noise damper By attaching the noise damper to the IC recorder, you can reduce vibration noises from a table or other surface where the IC recorder is placed. Align the lower part of the noise damper to the recorder at an angle (), and then press the logo part (), so that the noise damper clicks in place.  Clip  POWER•HOLD switch  microSD card slot   (headphone) jack  RESET button You can reset the IC recorder by pressing the button with a small pin, etc. ( p. 104).  To remove the noise damper Lift the upper part of the noise damper (in the reverse direction as described in ), and then remove it.  Tip The noise damper is for decreasing the possible noise from a table. When you attach the IC recorder to your clothes, remove the noise damper from the IC recorder.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121

µ
µ
Preparing the Recorder
Index
Table of
Contents
Rear
Clip
POWER•HOLD switch
microSD card slot
(headphone) jack
RESET button
You can reset the IC recorder by
pressing the button with a small pin,
etc. (
p. 104).
Attaching the noise damper
By attaching the noise damper to the
IC recorder, you can reduce
vibration noises from a table or
other surface where the IC recorder
is placed.
Align the lower part of the noise
damper to the recorder at an angle
(
), and then press the logo part
(
), so that the noise damper clicks
in place.
To remove the noise damper
Lift the upper part of the noise damper
(in the reverse direction as described in
), and then remove it.
Tip
The noise damper is for decreasing the
possible noise from a table. When you
attach the IC recorder to your clothes,
remove the noise damper from the IC
recorder.