Stihl MS 311 User Manual - Page 41

magnet poles arrows are next

Get Stihl MS 311 PDF manuals and user guides View all Stihl MS 311 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

4903RA259 TG 3 42 1 1 - Check operation - rotate the flywheel and make sure it does not touch the ignition module. 4903RA095 TG 4903RA273 TG The ignition module (1) and ignition lead (2) form a unit. - Before installing, check that the sleeve (4) is on the ignition lead (2) and its opening (arrow) is pointing in the same direction as the spark plug boot. : Push the ignition module back and slide the setting gauge (1) 1111 890 6400 between the arms of the ignition module and the flywheel magnet. - Inspect the spark plug boot (3) and replace if necessary, b 7.5 - Troubleshooting, b 2.3 1 1 : Connect the short circuit wire terminal (1) - the terminal must be pushed fully home. 4903RA258 TG Installing 1 The setting gauge is not shown in the illustration. - Push the ignition module (1) back : Starting at the ignition module, 3 and hold it there push the ignition lead into the cable channel. - the flywheel must move freely. 4903RA256 TG 2 : Fit the ignition module (1) and insert the screw (arrow) - do not tighten down yet. : Fit the ground wire (3) and insert the screw (2) - do not tighten down yet. Crimped side of terminal must face the screw head. : Rotate the flywheel until the magnet poles (arrows) are next to the ignition module (1). - Press the ignition module (1) against the setting gauge. Hold the ground wire terminal steady - it must point towards the cable guide. - Tighten down the screws firmly. - Remove the setting gauge. 4903RA097 TG 40 MS 311, MS 391

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
40
MS 311, MS 391
The ignition module (1) and ignition
lead (2) form a unit.
–
Before installing, check that the
sleeve (4) is on the ignition
lead
(2) and its opening
(arrow) is
pointing in the same direction as
the spark plug boot.
–
Inspect the spark plug boot (3)
and replace if necessary,
b
7.5
– Troubleshooting,
b
2.3
Installing
:
Fit the ignition module (1) and
insert the screw (arrow)
– do not tighten down yet.
:
Fit the ground wire (3) and insert
the screw (2) – do not tighten
down yet.
Crimped side of terminal must face
the screw head.
4903RA273 TG
4
1
2
3
1
4903RA256 TG
3
2
:
Push the ignition module back
and slide the setting gauge (1)
1111 890 6400 between the
arms of the ignition module and
the flywheel magnet.
The setting gauge is not shown in
the illustration.
–
Push the ignition module (1) back
and hold it there
– the flywheel must move freely.
:
Rotate the flywheel until the
magnet poles (arrows) are next to
the ignition module (1).
–
Press the ignition module (1)
against the setting gauge.
Hold the ground wire terminal
steady – it must point towards the
cable guide.
–
Tighten down the screws firmly.
–
Remove the setting gauge.
4903RA095 TG
1
4903RA258 TG
1
–
Check operation – rotate the
flywheel and make sure it does
not touch the ignition module.
:
Connect the short circuit wire
terminal (1)
– the terminal must
be pushed fully home.
:
Starting at the ignition module,
push the ignition lead into the
cable channel.
1
4903RA259 TG
4903RA097 TG