Stihl MS 311 User Manual - Page 46

Push the ring terminal 1 onto

Get Stihl MS 311 PDF manuals and user guides View all Stihl MS 311 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing Position the short circuit wire so that 1 it forms a loop and can move along with the switch shaft. 4903RA103 TG 4903RA104 TG 1 : Position the short circuit wire so that the yellow mark lines up with the edge (arrow). - Push the wiring harness (1) into the guide. The wire must be laid straight and fit snugly against the housing. : Push the short circuit wire (1) into the guides (arrows). : Check that short circuit wire is properly seated, push it fully into the guide (arrow) if necessary. 4903RA109 TG 4903RA110 TG 1 1 4903RA107 TG 1 4903RA105 TG 2 - Install the filter base, b 12.3 : Position the protective tube (2) so that it is in line with the yellow mark (arrow). : Push the protective tube (2) with short circuit wire (1) into the guide (centered as shown). - Position the ring terminal (1) so that its crimped side faces up. : Push the ring terminal (1) onto the pin (arrow) as far as stop. 2 - Position the ring terminal (1) so that its crimped side faces up. : Fit the ring terminal (1) of the ground wire on the pin (2) and swing it down. 4903RA261 TG 1 : Push the short circuit wire (1) into the guides (arrows). MS 311, MS 391 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
45
MS 311, MS 391
Installing
:
Position the short circuit wire so
that the yellow mark lines up with
the edge (arrow).
–
Push the wiring harness (1) into
the guide.
:
Position the protective tube (2)
so that it is in line with the yellow
mark (arrow).
:
Push the protective tube (2) with
short circuit wire (1) into the
guide (centered as shown).
4903RA104 TG
1
4903RA105 TG
1
2
The wire must be laid straight and fit
snugly against the housing.
:
Push the short circuit wire
(1) into
the guides (arrows).
–
Install the filter base,
b
12.3
–
Position the ring terminal (1) so
that its crimped side faces up.
:
Push the ring terminal (1) onto
the pin (arrow) as far as stop.
:
Push the short circuit wire
(1) into
the guides (arrows).
4903RA103 TG
1
4903RA107 TG
1
4903RA261 TG
1
Position the short circuit wire so that
it forms a loop and can move along
with the switch shaft.
:
Check that short circuit wire is
properly seated, push it fully into
the guide (arrow) if necessary.
–
Position the ring terminal (1) so
that its crimped side faces up.
:
Fit the ring terminal (1) of the
ground wire on the pin (2) and
swing it down.
4903RA109 TG
4903RA110 TG
2
1