TP-Link Archer C2 Archer C2 V1 User Guide 1910010993 - Page 37

Service Name/Server Name

Get TP-Link Archer C2 PDF manuals and user guides View all TP-Link Archer C2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Archer C2 AC750 Wireless Dual Band Gigabit Router  Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. If you want to do some advanced configurations, please click the Advanced button, and the page shown in Figure 4-6 will then appear: Figure 4-6 PPPoE Advanced Settings  Service Name/Server Name - The service name and server name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.  MTU(Bytes) - The default MTU size is "1480" bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP.  Enable Fullcone NAT - It is a type of NAT, if not enabled, the default NAT will act.  Enable IGMP Proxy - IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. The default value is enabled, and if you are not sure, please contact your ISP or just leave it.  ISP Specified IP Address - If your ISP does not automatically assign IP addresses to the router during login, please click "Use IP address specified by ISP" check box and enter the IP address provided by your ISP in dotted-decimal notation. - 27 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 27 -
Connect Manually -
You can click the Connect/Disconnect button to connect/disconnect
immediately. This mode also supports the
Max Idle Time
function as Connect on Demand
mode. The Internet connection can be disconnected automatically after a specified inactivity
period and re-established when you attempt to access the Internet again.
Click the
Connect
button to connect immediately. Click the
Disconnect
button to disconnect
immediately.
Caution
: Sometimes the connection cannot be terminated although you specify a time to Max Idle
Time because some applications are visiting the Internet continually in the background.
If you want to do some advanced configurations, please click the
Advanced
button, and the page
shown in Figure 4-6 will then appear:
Figure 4-6 PPPoE Advanced Settings
Service Name/Server Name -
The service name and server name should not be configured
unless you are sure it is necessary for your ISP.
In most cases, leaving these fields blank will
work.
MTU(Bytes) -
The default MTU size is “1480” bytes, which is usually fine. It is not
recommended that you change the default
MTU Size
unless required by your ISP.
Enable Fullcone NAT -
It is a type of NAT, if not enabled, the default NAT will act.
Enable IGMP Proxy
-
IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is enabled, and if you are not
sure, please contact your ISP or just leave it.
ISP Specified IP Address -
If your ISP does not automatically assign IP addresses to the
router during login, please click “
Use IP address specified by ISP
” check box and enter the
IP address provided by your ISP in dotted-decimal notation.