Home » TP-Link Manuals » Bridges & Routers » TP-Link Archer C2 » Manual Viewer

TP-Link Archer C2 Archer C2 V1 User Guide 1910010993 - Page 92

Advanced Security

Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Archer C2 AC750 Wireless Dual Band Gigabit Router the use of cryptographic security services. To allow IPSec tunnels to pass through the router, click Enable.  ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc.  FTP ALG - To allow FTP clients and servers to transfer data across NAT, click Enable.  TFTP ALG - To allow TFTP clients and servers to transfer data across NAT, click Enable.  H323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, click Enable.  SIP ALG - To allow SIP clients and servers to communicate across NAT,click Enable.  RTSP ALG - To allow some media player clients to communicate with some streaming media servers across NAT, click Enable. Click the Save button to save your settings. 4.13.2 Advanced Security Choose menu "Security → Advanced Security", and then you can protect the router from being attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the screen as shown in Figure 4-70. Figure 4-70 Advanced Security  DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. - 82 -

Section	Page
Package Contents	11
Chapter 1. Introduction	12
1.1 Overview of the Router	12
1.2 Conventions	13
1.3 Main Features	13
1.4 Panel Layout	14
1.4.1 The Front Panel	14
1.4.2 The Rear Panel	15
Chapter 2. Connecting the router	17
2.1 System Requirements	17
2.2 Installation Environment Requirements	17
2.3 Connecting the Router	17
Chapter 3. Quick Installation Guide	19
3.1 TCP/IP Configuration	19
3.2 Quick Installation Guide	21
Chapter 4. Configuring the router	31
4.1 Login	31
4.2 Status	31
4.3 Quick Setup	32
4.4 Network	33
4.4.1 WAN	33
4.4.2 LAN	43
4.4.3 MAC Clone	44
4.5 Dual Band Selection	44
4.6 Wireless 2.4GHz	45
4.6.1 Basic Settings	45
4.6.2 WPS	48
4.6.3 Wireless Security	50
4.6.4 Wireless MAC Filtering	54
4.6.5 Wireless Advanced	56
4.6.6 Wireless Statistics	57
4.7 Wireless 5GHz	58
4.7.1 Basic Settings	58
4.7.2 WPS	60
4.7.3 Wireless Security	63
4.7.4 Wireless MAC Filtering	67
4.7.5 Wireless Advanced	69
4.7.6 Wireless Statistics	70
4.8 Guest Network	71
4.9 DHCP	72
4.9.1 DHCP Settings	72
4.9.2 DHCP Clients List	74
4.9.3 Address Reservation	74
4.10 USB Settings	76
4.10.1 USB Mass Storagre	76
4.10.2 User Accounts	76
4.10.3 Storage Sharing	78
4.10.4 FTP Server	80
4.10.5 Media Server	81
4.10.6 Print Server	83
4.11 NAT	84
4.12 Forwarding	84
4.12.1 Virtual Servers	85
4.12.2 Port Triggering	86
4.12.3 DMZ	88
4.12.4 UPnP	89
4.13 Security	90
4.13.1 Basic Security	90
4.13.2 Advanced Security	92
4.13.3 Local Management	93
4.13.4 Remote Management	94
4.14 Parent Control	95
4.15 Access Control	98
4.15.1 Rule	99
4.15.2 Host	101
4.15.3 Target	103
4.15.4 Schedule	106
4.16 Advanced Routing	107
4.16.1 Static Route List	108
4.16.2 System Routing Table	109
4.17 Bandwidth Control	110
4.18 IP & MAC Binding	111
4.18.1 Binding Settings	111
4.18.2 ARP List	112
4.19 Dynamic DNS	113
4.19.1 No-ip.com DDNS	113
4.19.2 Comexe.cn DDNS	114
4.19.3 Dyndns.org DDNS	115
4.20 IPv6	116
4.20.1 IPv6 Status	117
4.20.2 IPv6 WAN	118
4.20.3 IPv6 LAN	122
4.21 System Tools	123
4.21.1 Time Settings	123
4.21.2 Diagnostic	125
4.21.3 Firmware Upgrade	127
4.21.4 Factory Defaults	128
4.21.5 Backup & Restore	128
4.21.6 Reboot	129
4.21.7 Password	129
4.21.8 System Log	130
4.21.9 Statistics	131
4.22 Logout	133
Appendix A: FAQ	134
Appendix B: Configuring the PC	139
Appendix C: Specifications	141