TRENDnet TEW-740APBO Users Guide - Page 38

Wireless Network Expansion, Wireless General Setup

Get TRENDnet TEW-740APBO PDF manuals and user guides View all TRENDnet TEW-740APBO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

TRENDnet User's Guide TEW-740APBO o Primary: The IP address of the primary DNS server. o Secondary: The IP address of the secondary DNS server.  802.1d Spanning Tree The spanning tree network protocol provides a loop free topology for a bridged LAN between LAN interface and 4 WDS interfaces from wds0 to wds3. The Spanning Tree Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. The Spanning tree always enabled on the access point. Below Figures depict a loop for a bridged LAN between LAN and WDS link Click Save button to save your changes. Click Reboot button to activate your changes Wireless Network Expansion The network manager can configure related wireless settings, General Settings, Advanced Settings and WDS Settings. Wireless General Setup The administrator can change the data transmission, channel and output power settings for the system. Please click on Wireless -> General Setup and follow the below setting.  MAC Address: The MAC address of the Wireless interface is displayed here.  Band Mode: Select an appropriate wireless band; bands available are 801.11b, 802.11b/g, 802.11b/g/n or 802.11n only.  Channel: Select the desired channel from the drop-down list to have the access point operate on. Click Auto Scan to scan for the best available channel to use based on the environment.  Tx Power: You can adjust the output power of the system to get the appropriate coverage for your wireless network. Specify digit numbers between 1 to 100 (the unit is %) for your environment. If you are not sure which setting to choose, then keep the default setting, 100%.  RF (ON/OFF) Schedule: Select an assigned schedule of when to have the access point turn on. Select Always Run to have the access point always on. When Band Mode select in 802.11a only mode, the HT(High Throughput) settings should be hidden immediately. © Copyright 2016 TRENDnet. All Rights Reserved.  TxStream/Rx Stream: Select the amount of transmit (TX) and Receive (RX) streams. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
38
o
Primary:
The IP address of the primary DNS server.
o
Secondary:
The IP address of the secondary DNS server.
802.1d Spanning Tree
The spanning tree network protocol provides a loop free topology for a bridged LAN
between LAN interface and 4 WDS interfaces from wds0 to wds3. The Spanning Tree
Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. The
Spanning tree always enabled on the access point. Below Figures depict a loop for a
bridged LAN between LAN and WDS link
Click
Save
button to save your changes. Click
Reboot
button to activate your changes
Wireless Network Expansion
The network manager can configure related wireless settings,
General Settings,
Advanced Settings
and
WDS Settings
.
Wireless General Setup
The administrator can change the data transmission, channel and output power settings
for the system. Please click on
Wireless -> General Setup
and follow the below setting.
MAC Address:
The MAC address of the Wireless interface is displayed here.
Band Mode:
Select an appropriate wireless band; bands available are 801.11b,
802.11b/g,
802.11b/g/n or 802.11n only.
Channel:
Select the desired channel from the drop-down list to have the access
point operate on. Click
Auto Scan
to scan for the best available channel to use
based on the environment.
Tx Power:
You
can adjust the output power of the system to get the appropriate
coverage for your wireless network. Specify digit numbers between 1 to 100 (the
unit is %) for your environment. If you are not sure which setting to choose, then
keep the default setting,
100
%.
RF (ON/OFF) Schedule:
Select an assigned schedule of when to have the access
point turn on. Select
Always Run
to have the access point always on.
When
Band Mode
select in
802.11a only mode
, the
HT(High Throughput)
settings
should be hidden immediately.
TxStream/Rx Stream:
Select the amount of transmit (TX) and Receive (RX) streams.