TRENDnet TEW-740APBO Users Guide - Page 69

Site Survey, Create Wireless Profile

Get TRENDnet TEW-740APBO PDF manuals and user guides View all TRENDnet TEW-740APBO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

TRENDnet User's Guide  WMM Parameters of Station: This affects traffic flowing from the client station to the access point. o Aifsn : The Arbitration Inter-Frame Spacing Number specifies a wait time (in milliseconds) for data frames o CWmin : Minimum Contention Window. This parameter is input to the algorithm that determines the initial random backoff wait time ("window") for retry of a transmission. The value specified here in the Minimum Contention Window is the upper limit (in milliseconds) of a range from which the initial random backoff wait time is determined. o CWmax : Maximum Contention Window. The value specified here in the Maximum Contention Window is the upper limit (in milliseconds) for the doubling of the random backoff value. This doubling continues until either the data frame is sent or the Maximum Contention Window size is reached. Once the Maximum Contention Window size is reached, retries will continue until a maximum number of retries allowed is reached. Valid values for the "cwmax" are 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1024. The value for "cwmax" must be higher than the value for "cwmin". o Txop : Transmission Opportunity is an interval of time when a WME AP has the right to initiate transmissions onto the wireless medium (WM). This value specifies (in milliseconds) the Transmission Opportunity (Txop) for AP; that is, the interval of time when the WMM AP has the right to initiate transmissions on the wireless network. o ACM: Admission Control Mandatory, ACM only takes effect on AC_VI and AC_VO. When you do not click Checkbox, it means that the ACM is controlled by the connecting AP. If you click Checkbox, it means that the Client is in charge. Click Save button to save your changes. Click Reboot button to activate your changes. The items in this page are for AP's RF advanced settings and will be applied to all VAPs and WDS Links. Site Survey Use this tool to scan and locate WISP Access Points and select one to associate with. Please click on Wireless -> Site Survey. Below depicts an example for site survey. TEW-740APBO  ESSID: Available Extend Service Set ID of surrounding Access Points.  MAC Address: MAC addresses of surrounding Access Points.  Signal: Received signal strength of all found Access Points.  Channel: Channel numbers used by all found Access Points.  Security: Security type by all found Access Points.  Band: Wireless band used by all found Access Points.  Network Type: Network type used by all found Access Points.  Select: Click "Select" to configure settings and associate with chosen AP. Create Wireless Profile The administrator can configure station profiles via this page. Please click on Wireless -> Wireless Profile and follow the below setting.  Connection Setup: Select the repeater connection type. o Fix: Select to have access point fixed on one profile to repeat o Cycle: Select to have access point cycle through different profiles.  General Configuration: © Copyright 2016 TRENDnet. All Rights Reserved. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
69
WMM Parameters of Station:
This affects traffic flowing from the client station to
the access point.
o
Aifsn
: The Arbitration Inter-Frame Spacing Number specifies a wait time (in
milliseconds) for data frames
o
CWmin
: Minimum Contention Window. This parameter is input to the
algorithm that determines the initial random backoff wait time ("window")
for retry of a transmission. The value specified here in the Minimum
Contention Window is the upper limit (in milliseconds) of a range from
which the initial random backoff wait time is determined.
o
CWmax
: Maximum Contention Window. The value specified here in the
Maximum Contention Window is the upper limit (in milliseconds) for the doubling
of the random backoff value. This doubling continues until either the data frame
is sent or the Maximum Contention Window size is reached. Once the Maximum
Contention Window size is reached, retries will continue until a maximum
number of retries allowed is reached. Valid values for the "cwmax" are 1, 3, 7, 15,
31, 63, 127, 255, 511, or 1024. The value for "cwmax" must be higher than the
value for "cwmin".
o
Txop
: Transmission Opportunity is an interval of time when a WME AP has the
right to initiate transmissions onto the wireless medium (WM). This value
specifies (in milliseconds) the Transmission Opportunity (Txop) for AP; that is, the
interval of time when the WMM AP has the right to initiate transmissions on the
wireless network.
o
ACM:
Admission Control Mandatory, ACM only takes effect on AC_VI and AC_VO.
When you do not click Checkbox, it means that the ACM is controlled by the
connecting AP. If you click Checkbox, it means that the Client is in charge.
Click
Save
button to save your changes. Click
Reboot
button to activate your changes.
The items in this page are for AP's RF advanced settings and will be applied to
all VAPs
and
WDS Links
.
Site Survey
Use this tool to scan and locate WISP Access Points and select one to associate with.
Please click on
Wireless -> Site Survey
. Below depicts an example for site survey.
ESSID:
Available Extend Service Set ID of surrounding Access Points.
MAC Address:
MAC addresses of surrounding Access Points.
Signal:
Received signal strength of all found Access Points.
Channel:
Channel numbers used by all found Access Points.
Security:
Security type by all found Access Points.
Band:
Wireless band used by all found Access Points.
Network Type:
Network type used by all found Access Points.
Select:
Click “
Select
” to configure settings and associate with
chosen AP.
Create Wireless Profile
The administrator can configure station profiles via this page.
Please click on
Wireless -> Wireless Profile
and follow the below setting.
Connection
Setup:
Select the repeater connection type.
o
Fix:
Select to have access point fixed on one profile to repeat
o
Cycle:
Select to have access point cycle through different profiles.
General Configuration: