TRENDnet TEW-740APBO Users Guide - Page 65

Con Static IP address, Access Point Association, Wireless General Setup, RF ON/OFF Schedule

Get TRENDnet TEW-740APBO PDF manuals and user guides View all TRENDnet TEW-740APBO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

TRENDnet User's Guide o Lease Time: The IP addresses given out by the DHCP server will only be valid for the duration specified by the lease time. Increasing the time ensure client operation without interruptions, but could introduce potential conflicts. Lowering the lease time will avoid potential address conflicts, but might cause more interruptions to the client while it will acquire new IP addresses from the DHCP server. Default is 86400 seconds Click Save button to save your changes. Click Reboot button to activate your changes Configure Static IP address Assign static IP address to associated clients through the access point.  Comment: Enter a note of assigned IP address  IP Address: Enter the IP address to assign  MAC address: Enter the client MAC address to the assigned IP address. Click Add to enter settings. TEW-740APBO Access Point Association Wireless General Setup The administrator can change the data transmission, channel and output power settings for the system. Please click on Wireless -> General Setup and follow the below setting.  MAC Address: The MAC address of the Wireless interface is displayed here.  Band Mode: Select an appropriate wireless band; bands available are 801.11b, 802.11b/g, 802.11b/g/n or 802.11n only.  Channel: Select the desired channel from the drop-down list to have the access point operate on. Click Auto Scan to scan for the best available channel to use based on the environment.  Tx Power: You can adjust the output power of the system to get the appropriate coverage for your wireless network. Specify digit numbers between 1 to 100 (the unit is %) for your environment. If you are not sure which setting to choose, then keep the default setting, 100%.  RF (ON/OFF) Schedule: Select an assigned schedule of when to have the access point turn on. Select Always Run to have the access point always on. When Band Mode select in 802.11a only mode, the HT(High Throughput) settings should be hidden immediately. © Copyright 2016 TRENDnet. All Rights Reserved. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
65
o
Lease Time:
The IP addresses given out by the DHCP server will only be valid for
the duration specified by the lease time. Increasing the time ensure client
operation without interruptions, but could introduce potential conflicts. Lowering
the lease time will avoid potential address conflicts, but might cause more
interruptions to the client while it will acquire new IP addresses from the DHCP
server. Default is
86400
seconds
Click
Save
button to save your changes. Click
Reboot
button to activate your changes
Configure Static IP address
Assign static IP address to associated clients through the access point.
Comment:
Enter a note of assigned IP address
IP Address:
Enter the IP address to assign
MAC address:
Enter the client MAC address to the assigned IP address. Click Add to
enter settings.
Access Point Association
Wireless General Setup
The administrator can change the data transmission, channel and output power settings
for the system. Please click on
Wireless -> General Setup
and follow the below setting.
MAC Address:
The MAC address of the Wireless interface is displayed here.
Band Mode:
Select an appropriate wireless band; bands available are 801.11b,
802.11b/g, 802.11b/g/n or 802.11n only.
Channel:
Select the desired channel from the drop-down list to have the access
point operate on. Click
Auto Scan
to scan for the best available channel to use
based on the environment.
Tx Power:
You
can adjust the output power of the system to get the appropriate
coverage for your wireless network. Specify digit numbers between 1 to 100 (the
unit is %) for your environment. If you are not sure which setting to choose, then
keep the default setting,
100
%.
RF (ON/OFF) Schedule:
Select an assigned schedule of when to have the access
point turn on. Select
Always Run
to have the access point always on.
When
Band Mode
select in
802.11a only mode
, the
HT(High Throughput)
settings
should be hidden immediately.