Yamaha PSR-8000 Owner's Manual - Page 179
Channel Mode Messages, 3 Registered Parameter Number Rpn, 5 System Realtime Messages
View all Yamaha PSR-8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 179 highlights
,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,QMIDI,QData,QForma,Qt • ATTACK TIME applies adjustment to the envelope attack time set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. • BRIGHTNESS applies adjustment to the cut-off frequency set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. Lower voices produce a softer sound. For some voices the effective parameter range is narrower than the legal parameter range. (3-2) CHANNEL MODE MESSAGES STATUS 1011nnnn (BnH) CONTROL NUMBER 0ccccccc CONTROL VALUE 0vvvvvvv n = 0 - 15 VOICE CHANNEL NUMBER c = CONTROL NUMBER v = DATA VALUE (3-2-1) ALL SOUND OFF (Receive only) (CONTROL NUMBER = 78H , DATA VALUE = 0) Switches off all sound from the channel. Does not reset Note On and Hold On conditions established by Channel Messages. (3-2-2) RESET ALL CONTROLLERS (Receive only) (CONTROL NUMBER = 79H , DATA VALUE = 0) Resets controllers as follows. PITCH BEND CHANGE AFTER TOUCH MODULATION EXPRESSION SUSTAIN SOSTENUTO SOFT PEDAL NRPN RPN PORTAMENT CONTROL PORTAMENTO 0 (Center) 0 (min.) 0 (min.) 127 (max.) 0 (off) 0 (off) 0 (off) Sets number to null. (Internal data remains unchanged) Sets number to null. (Internal data remains unchanged) Resets portamento source note number 0 (off) (3-2-3) ALL NOTES OFF (Receive only) (CONTROL NUMBER = 7BH , DATA VALUE = 0) Switches off all of the channel's "on" notes. However, any notes being held by SUSTAIN or SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off. (3-2-4) OMNI OFF (Receive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0) Same processing as for All Notes Off. (3-2-5) OMNI ON (Receive only) (CONTROL NUMBER = 7DH , DATA VALUE = 0) Same processing as for All Notes Off. Omni On is not executed. (3-2-6) MONO (Receive only) (CONTROL NUMBER = 7EH , DATA VALUE = 0 - 16) Same processing as for All Sounds Off. If the 3rd byte is in a range of 0-16 the corresponding channel will be changed to Mode 4 (m=1). (3-2-7) POLY (Receive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0) Same processing as for All Sounds Off and the corresponding channel will be changed to Mode 3. (3-3) REGISTERED PARAMETER NUMBER (RPN) STATUS 1011nnnn (BnH) n = 0 - 15 VOICE CHANNEL NUMBER RPN LSB 01100100 (64H) RPN LSB NUMBER 0ppppppp pp = RPN LSB(refer to the list below) RPN MSB 01100101 (65H) RPN MSB NUMBER 0qqqqqqq qq = RPN MSB(refer to the list below) DATA ENTRY MSB 00000110 (06H) DATA VALUE 0mmmmmmm mm = Data Value DATA ENTRY LSB 00100110 (26H) DATA VALUE 0lllllll ll = Data Value First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry MSB/LSB. RPN D.ENTRY LSB MSB MSB LSB PARAMETER NAME DATA RANGE 00H 00H mmH - PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones) 01H 00H mmH llH FINE TUNE {mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH} (-8192*100/8192) - 0 - (+8192*100/8192) 02H 00H mmH - COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones) 7FH 7FH - - NULL Clears the current RPN number setting. Does not change the internal parameter settings. (3-4) NON-REGISTERED PARAMETER NUMBER (NRPN) STATUS 1011nnnn (BnH) n = 0 - 15 VOICE CHANNEL NUMBER NRPN LSB 01100010 (62H) NRPN LSB NUMBER 0ppppppp pp = NRPN LSB(refer to the list below) NRPN MSB 01100011 (63H) NRPN MSB NUMBER 0qqqqqqq qq = NRPN MSB(refer to the list below) DATA ENTRY MSB 00000110 (06H) DATA VALUE 0mmmmmmm mm = Data Value First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry MSB/LSB. NRPN MSB LSB 01H 08H 01H 09H 01H 0AH 01H 20H 01H 21H 01H 63H 01H 64H 01H 66H 14H rrH 15H rrH 16H rrH 17H rrH 18H rrH 19H rrH 1AH rrH 1CH rrH 1DH rrH 1EH rrH 1FH rrH D.ENTRY MSB LSB mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - mmH - PARAMETER NAME DATA RANGE VIBRATO RATE 00H - 40H - 7FH (-64 - 0 - +63) VIBRATO DEPTH 00H - 40H - 7FH (-64 - 0 - +63) VIBRATO DELAY 00H - 40H - 7FH (-64 - 0 - +63) FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 - 0 - +63) FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) EG ATTACK TIME 00H - 40H - 7FH (-64 - 0 - +63) EG DECAY TIME 00H - 40H - 7FH (-64 - 0 - +63) EG RELEASE 00H - 40H - 7FH (-64 - 0 - +63) DRUM FILTER CUTOFF FREQ. 00H - 40H - 7FH (-64 - 0 - +63) DRUM FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) DRUM AEG ATTACK RATE 00H - 40H - 7FH (-64 - 0 - +63) DRUM AEG DECAY RATE 00H - 40H - 7FH (-64 - 0 - +63) DRUM PITCH COARSE 00H - 40H - 7FH (-64 - 0 - +63) DRUM PITCH FINE 00H - 40H - 7FH (-64 - 0 - +63) DRUM LEVEL 00H - 7FH (0 - max.) DRUM PANPOT 00H ,01H - 40H - 7FH (random,left - center - right) DRUM REVERB SEND LEVEL 00H - 7FH (0 - max.) DRUM CHORUS SEND LEVEL 00H - 7FH (0 - max.) DRUM VARIATION SEND LEVEL 00H - 7FH (0 - max.) The MSG14H-1FH (for drums) message is accepted as long as the channel is set with a drum voice. rrH : drum instrument note number (3-5) SYSTEM REALTIME MESSAGES (3-5-1) MIDI CLOCK STATUS 11111000 (F8H) Transmission: 96 clocks per measure are transmitted. Reception: If the instrument's clock is set to external, after FAH is received from the external device the instrument's clock will sync with the 96 beats per measure received from the external device. Decides whether the internal clock, or Timing Clocks received via the MIDI IN will be used. (3-5-2) START STATUS 11111010 (FAH) Transmission: Transmitted when instrument's Rhythm or Song playback is started. Reception: If the instrument's clock is set to external, Rhythm, Song Playback, or Song Rec will start. (3-5-3) STOP STATUS 11111100 (FCH) Transmission: Transmitted when instrument's Rhythm or Song playback is stopped. Reception: If the instrument's clock is set to external, Rhythm, Song Playback, or Song Rec will stop. (3-5-4) ACTIVE SENSING STATUS 11111110 (FEH) Transmission: Transmitted approximately once every 200msec. Reception: Sensing is started once this Code is received. If Status or Data is not received within 400ms, the MIDI Receive Buffer will be cleared, and all notes, including those being sustained, will be cut OFF. Also, all control values will be reset to their factory defaults. (3-6) SYSTEM EXCLUSIVE MESSAGE (3-6-1) YAMAHA MIDI FORMAT (3-6-1-1) SECTION CONTROL binary hexadecimal 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 01111110 7E Style 00000000 00 0sssssss SS Switch No. 00H : INTRO A 01H~07H : INTRO B 08H : MAIN A 09H~0FH : MAIN B 10H : FILL IN AA 11H~17H : FILL IN BB 18H : FILL IN AB 19H~1FH : FILL IN BA 20H : ENDING A 21H~27H : ENDING B 0ddddddd DD Switch On/Off : 00H (Off),7FH (On) 11110111 F7 End of Exclusive When an ON code is received, the appointed section will be changed. 179