Brother International LK3-B432E MKII Instruction Manual - English - Page 41

at this time., Apply grease to the outside of the collar

Get Brother International LK3-B432E MKII PDF manuals and user guides View all Brother International LK3-B432E MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

10 . STANDARD ADJUSTMENTS 10-7-1 . Replacing the movable knife and fixed knife q w y e y t r i u 1. Open the large shuttle hook cover, remove the screws q and w, and then remove the feed plate e. 2. Remove the two screws r and the two screws t, and then remove the needle plate y. 3. Remove the thread trimmer connecting rod u from the connecting rod lever pin i. o !2 !3 !1 !0 0.5mm !0 4. Remove the movable knife o and replace it with a new one. At this time, check that the movable knife o and the fixed knife !0 cut the thread cleanly. If necessary, adjust by using the appropriate movable knife washer !1 (supplied as accessories). * Apply grease to the outside of the collar !2 at this time. 5. Install the fixed knife !0 at a distance of 0.5 mm from the needle hole plate !3. 6. Place the thread trimming connecting rod uonto the connecting rod lever pin i, and then install to the needle plate y. 35 LK3-B430E-, B431E-, B432E-, B433E- Mark II

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
35
LK3-B430E-, B431E-, B432E-, B433E- Mark II
q
w
e
r
t
y
o
!
1
!
0
y
u
i
!
0
!
3
10-7-1 . Replacing the movable knife and fixed knife
1.
Open the large shuttle hook cover, remove the screws
q
and
w
, and then remove the feed plate
e
.
2.
Remove the two screws
r
and the two screws
t
, and then remove the needle plate
y
.
3.
Remove the thread trimmer connecting rod
u
from the connecting rod lever pin
i
.
4.
Remove the movable knife
o
and replace it with a new one. At this time, check that the movable knife
o
and the fixed knife
!0
cut the thread cleanly. If necessary, adjust by using the appropriate movable knife
washer
!1
(supplied as accessories).
* Apply grease to the outside of the collar
!2
at this time.
5.
Install the fixed knife
!0
at a distance of 0.5 mm from the needle hole plate
!3
.
6.
Place the thread trimming connecting rod
u
onto the connecting rod lever pin
i
, and then install to the
needle plate
y
.
10 . STANDARD ADJUSTMENTS
0.5mm
!
2