Brother International MD-817 Service Manual - Page 108

Brother International MD-817 Manual

Get Brother International MD-817 PDF manuals and user guides View all Brother International MD-817 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

0 Assembly (1) Pass the cable of the new frame assembly through bracket assembly L. When doing so, note the following. 1) Be careful that the cable is not caught in the frame. 2) Be sure to align the bracket's rib with the space of the upper magnet in the frame. Bracket Assembly L Cable Frame Assembly Space of upper magnet in frame Bracket rib (Fig. 2) (2) Align the projection of bracket R with the groove of bracket L, and then try insertion. Note that insertion cannot be completed unless the rib within bracket R is aligned with the clearance of the upper magnet within the frame. For alignment, move the position of the frame assembly. 0 Align R (3) When the installation position of the frame assembly is adjusted, remove bracket R once again and push the rotor all the way into bracket L. At this time the rotor must be grasped tightly so that the commutator part of the rotor does not make contact with the magnet inside the frame. Be sure not to forget to check whether or not the spring washer is included. Vat ;111=1)))))) 01111MIMMIIIMIna PAS, Commutator (4) Install bracket R so that it is positioned with bracket L as described in 2. above. When the position is correct, gently tap it in using a wooden hammer. (5) Insert and tighten the four screws in the screw holes in bracket L. (Fig. 3) - 104 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
0
Assembly
(1)
Pass
the
cable
of
the
new
frame
assembly
through
bracket
assembly
L.
When
doing
so,
note
the
following.
1)
Be
careful
that
the
cable
is
not
caught
in
the
frame.
2)
Be
sure
to
align
the
bracket's
rib
with
the
space
of
the
upper
magnet
in
the
frame.
Bracket
Assembly
L
Cable
Frame
Assembly
Space
of
upper
magnet
in
frame
Bracket
rib
(Fig.
2)
(2)
Align
the
projection
of
bracket
R
with
the
groove
of
bracket
L,
and
then
try
insertion.
Note
that
insertion
cannot
be
completed
unless
the
rib
within
bracket
R
is
aligned
with
the
clearance
of
the
upper
magnet
within
the
frame.
For
alignment,
move
the
position
of
the
frame
assembly.
0
R
Align
(3)
When
the
installation
position
of
the
frame
assembly
is
adjusted,
remove
bracket
R
once
again
and
push
the
rotor
all
the
way
into
bracket
L.
At
this
time
the
rotor
must
be
grasped
tightly
so
that
the
commutator
part
of
the
rotor
does
not
make
contact
with
the
magnet
inside
the
frame.
Be
sure
not
to
forget
to
check
whether
or
not
the
spring
washer
is
included.
Commutator
(4)
Install
bracket
R
so
that
it
is
positioned
with
bracket
L
as
described
in
2.
above.
When
the
position
is
correct,
gently
tap
it
in
using
a
wooden
hammer.
(5)
Insert
and
tighten
the
four
screws
in
the
screw
holes
in
bracket
L.
Vat
;111=1))))))
01111MIMMIIIMIna
PAS
,
(Fig.
3)
-
104
-