Canon MultiPASS C755 Service Manual - Page 106

SW12 Switch 12: Report frame setting, T1 Timer Rx

Get Canon MultiPASS C755 PDF manuals and user guides View all Canon MultiPASS C755 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

MultiPASS C755 Chapter 3: Maintenance & Service #3 NUMERIC PARAM (numeric parameter settings) No. Function Selecting range 10 T0 Timer 0~9999 11 T1 Timer (Rx) 0~9999 13 Maximum time to receive 500~3000 one line of image data Default setting 5500 (55 second) 3500 (35 second) 1300 (13 second) [Parameter 10] The "wait time after transmission of a dialing signal ends until a significant signal is detected in transmission" was set as T1 timer with parameter 10. However, ITU-T recommends that it should be set as T0 timer, so parameter 10 has been renamed to T0 timer and the default time-out time has been changed from 35 to 55 seconds. The T1 timer for the transmitter (wait time after a CED, V21 flag, or ANSam significant signal is detected until the next significant signal is detected) is fixed at 35 seconds. NOTE [Parameter 11] Set the T1 timer for the receiver (wait time after DIS transmission starts until a significant signal is received). If frequent errors occur during reception (2 instances) because of line connection conditions, raise the value of this parameter. [Parameter 13] Set the maximum time to receive one line of image data when image data is received. If the other party is a computer fax and the time to receive one line of image data is long, raise the value of this parameter to increase the maximum reception (2 instances) time. #7 PRINTER (printer function settings) 1. SSSW SW12 (Switch 12: Report frame setting) Bit Function 0 Report frame lines 1 Report frame line types 2 Not used 3 Not used 4 Not used 5 Not used 6 Not used 7 Not used 1 OFF Dashed line 0 ON Solid line [Bit 0] Select whether to draw a frame for printing a report or list. [Bit 1] If a frame is drawn for printing a report or list, either a solid line or a dashed line can be selected. 3-55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
3-55
MultiPASS C755
Chapter 3: Maintenance & Service
#3 NUMERIC PARAM (numeric parameter settings)
No.
Function
Selecting range
Default setting
10
T0 Timer
0~9999
5500 (55 second)
11
T1 Timer (Rx)
0~9999
3500 (35 second)
13
Maximum time to receive
500~3000
1300 (13 second)
one line of image data
[Parameter 10]
The "wait time after transmission of a dialing signal ends until a significant signal is detected in
transmission" was set as T1 timer with parameter 10.
However, ITU-T recommends that it should be set as T0 timer, so parameter 10 has been renamed to
T0 timer and the default time-out time has been changed from 35 to 55 seconds.
The T1 timer for the transmitter (wait time after a CED, V21 flag, or ANSam significant
signal is detected until the next significant signal is detected) is fixed at 35 seconds.
[Parameter 11]
Set the T1 timer for the receiver (wait time after DIS transmission starts until a significant signal is
received).
If frequent errors occur during reception (2 instances) because of line connection conditions, raise
the value of this parameter.
[Parameter 13]
Set the maximum time to receive one line of image data when image data is received.
If the other party is a computer fax and the time to receive one line of image data is long, raise the
value of this parameter to increase the maximum reception (2 instances) time.
#7 PRINTER (printer function settings)
1. SSSW
SW12 (Switch 12: Report frame setting)
Bit
Function
1
0
0
Report frame lines
OFF
ON
1
Report frame line types
Dashed line
Solid line
2
Not used
3
Not used
4
Not used
5
Not used
6
Not used
7
Not used
[Bit 0]
Select whether to draw a frame for printing a report or list.
[Bit 1]
If a frame is drawn for printing a report or list, either a solid line or a dashed line can be selected.
NOTE