Canon MultiPASS C755 Service Manual - Page 79

Check Printer, Ink Abs Capa, 7 Printer

Get Canon MultiPASS C755 PDF manuals and user guides View all Canon MultiPASS C755 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

MultiPASS C755 Chapter 3: Maintenance & Service d) Recovery methods for codes indicated as "New" Note, however, the following supplementary information, as the machine requires different actions than the existing models to correct: ##085 Other party does not support ITU-T Color Faxing Solution: (1) Try sending again in black & white. (2) Check the received fax machine's setting for color faxing is available. ##342 Cleaning absorption waste ink capacity full Solution: Unlike errors that trigger the "CHECK PRINTER" message, This error is programmed so that it cannot be cleared using the Resume button. Replace the waste ink absorber as follows in the error occurs: (1) Select 3. INK ABS CAPA under #7 PRINTER in service mode, and the counter to 0. (2) Check to make sure that no image exist in memory; then, turn off the power, remove the appropriate parts, and replace the waste ink absorber. • V.8/V.34 protocol error codes ##670 [TX] At V.8 late start, the called party declares the V.8 protocol in DIS signal and this unit transmits a CI signal, but the protocol does not progress and a T1 time-out occurs. Cause: The other party disconnected the line while the CI signal was being transmitted, or ANSam/DIS from the called party was not able to be detected. Solution: Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set #1 SSSW SW-28 bit 0 to "1" to inhibit the V.8/V.34 protocol on calling. ##671 [RX] At V.8 termination, the protocol did not advance to phase 2 and a T1 time-out occurs after the caller CM signal was detected. Cause: Solution: The caller disconnected the line or the signal from the caller was not able to be detected. Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set #1 SSSW SW-28 bit 1 to "1" to inhibit the V.8/V.34 protocol for the called party. ##672 [TX] The protocol did not move from phase 2 to phase 3 and a T1 time-out occurred during V.34 transmission. Cause: Solution: The called party disconnected the line during phase 2 or the signal from the called party was not able to be detected. Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set #1 SSSW SW-28 bit 0 to "1" to inhibit the V.8/V.34 protocol on calling. ##673 [RX] The protocol did not move from phase 2 to phase 3 and a T1 time-out occurred during V.34 reception. Cause: Solution: The transmitter disconnected the line during phase 2 or the signal from the transmitter was not able to be detected. Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set #1 SSSW SW-28 bit 1 to "1" to inhibit the V.8/V.34 protocol on termination. 3-28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
3-28
MultiPASS C755
Chapter 3: Maintenance & Service
d) Recovery methods for codes indicated as “New”
Note, however, the following supplementary information, as the machine requires different actions than
the existing models to correct:
##085 Other party does not support ITU-T Color Faxing
Solution:
(1) Try sending again in black & white.
(2) Check the received fax machine’s setting for color faxing is available.
##342 Cleaning absorption waste ink capacity full
Solution:
Unlike errors that trigger the
“CHECK PRINTER”
message,
This error is
programmed so that it cannot be cleared using the
Resume
button.
Replace the
waste ink absorber as follows in the error occurs:
(1) Select
3. INK ABS CAPA
under
#7 PRINTER
in service mode, and the
counter to 0.
(2) Check to make sure that no image exist in memory; then, turn off the power,
remove the appropriate parts, and replace the waste ink absorber.
• V.8/V.34 protocol error codes
##670 [TX]
At V.8 late start, the called party declares the V.8 protocol in DIS signal and
this unit transmits a CI signal, but the protocol does not progress and a T1
time-out occurs.
Cause:
The other party disconnected the line while the CI signal was being transmitted, or
ANSam/DIS from the called party was not able to be detected.
Solution:
Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set
#1 SSSW SW-28 bit 0 to "1" to inhibit the V.8/V.34 protocol on calling.
##671 [RX]
At V.8 termination, the protocol did not advance to phase 2 and a T1 time-out
occurs after the caller CM signal was detected.
Cause:
The caller disconnected the line or the signal from the caller was not able to be
detected.
Solution:
Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set
#1 SSSW SW-28 bit 1 to "1" to inhibit the V.8/V.34 protocol for the called party.
##672 [TX]
The protocol did not move from phase 2 to phase 3 and a T1 time-out
occurred during V.34 transmission.
Cause:
The called party disconnected the line during phase 2 or the signal from the called
party was not able to be detected.
Solution:
Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set
#1 SSSW SW-28 bit 0 to "1" to inhibit the V.8/V.34 protocol on calling.
##673 [RX] The protocol did not move from phase 2 to phase 3 and a T1 time-out
occurred during V.34 reception.
Cause:
The transmitter disconnected the line during phase 2 or the signal from the
transmitter was not able to be detected.
Solution:
Increase #2 MENU No.07 transmission level within a range of -8~-15 (dBm) or set
#1 SSSW SW-28 bit 1 to "1" to inhibit the V.8/V.34 protocol on termination.