Cisco 3725 Software Configuration Guide - Page 103

Verifying the IP Address

Get Cisco 3725 - PRI Dial Bundle Router PDF manuals and user guides
UPC - 746320810911
View all Cisco 3725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Chapter 3 Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module Programming the Discrete Contact Points The discrete alarms do not require as much programming as the analog alarms. The AIC CLI commands available are the following: Command no exit description normally level Description Reversal option Exits current mode Sets the description. If no is set, then the description is not required. Sets the alarm's normal state to closed. If the no option is used, the normal state is set to open. This command applies only to points 1 - 56. Sets the alarm's level to the specified level. Verifying the IP Address To verify that the correct AIC IP address and IP route was entered, use the show run command. Below are samples of before-configuration and after-configuration show run command outputs: interface Serial5/0 ip unnumbered FastEthernet0/0 ! ip route 10.2.130.102 255.255.255.255 Serial5/0 ! alarm-interface 5 ip address 10.2.130.102 ********Before Configuration show run Output******* version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname uut2-3660 ! logging rate-limit console 10 except errors ! ip subnet-zero ! ! no ip finger no ip domain-lookup ! call rsvp-sync cns event-service server ! ! interface FastEthernet0/0 ip address 10.2.130.2 255.255.0.0 duplex auto speed auto no cdp enable OL-1957-04 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers 3-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
3-43
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 3
Configuring with the Command-Line Interface
Configuring the NM-AIC-64, Contact Closure Network Module
Programming the Discrete Contact Points
The discrete alarms do not require as much programming as the analog alarms. The AIC CLI commands
available are the following:
Verifying the IP Address
To verify that the correct AIC IP address and IP route was entered, use the
show
run
command. Below
are samples of before-configuration and after-configuration
show run command
outputs:
interface Serial5/0
ip unnumbered FastEthernet0/0
!
ip route 10.2.130.102 255.255.255.255
Serial5/0
!
alarm-interface 5
ip address 10.2.130.102
********Before Configuration show run Output*******
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname uut2-3660
!
logging rate-limit console 10 except errors
!
ip subnet-zero
!
!
no ip finger
no ip domain-lookup
!
call rsvp-sync
cns event-service server
!
!
interface FastEthernet0/0
ip address 10.2.130.2 255.255.0.0
duplex auto
speed auto
no cdp enable
Command
Description
no
Reversal option
exit
Exits current mode
description
Sets the description. If
no
is set, then the description
is not required.
normally
Sets the alarm’s normal state to closed. If the
no
option is used, the normal state is set to open. This
command applies only to points 1 - 56.
level
Sets the alarm’s level to the specified level.