Cisco 3725 Software Configuration Guide - Page 56

T1 Channelized Mode

Get Cisco 3725 - PRI Dial Bundle Router PDF manuals and user guides
UPC - 746320810911
View all Cisco 3725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Configuring Interface Parameters Chapter 2 Using the Setup Command Facility X.25 Encapsulation x25 circuit can be either in dce/dte mode. Choose from either dce/dte [dte]: Enter local x25 address: 1234 We will need to map the remote x.25 station's x25 address to the remote stations IP/IPX address Do you want to map the remote machine's x25 address to IP address? [yes]: IP address for the remote interface: 6.0.0.1 Do you want to map the remote machine's x25 address to IPX address? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed Enter remote x25 address: 4321 Enter lowest 2-way channel [1]: Enter highest 2-way channel [64]: Enter frame window (K) [7]: Enter Packet window (W) [2]: Enter Packet size (must be powers of 2) [128]: T1 Channelized Mode The following is an example of a T1 channelized mode configuration using the setup command facility: The following framing types are available: esf | sf Enter the framing type [esf]: The following linecode types are available: ami | b8zs Enter the line code type [b8zs]: T1 is capable of being configured for channel 1-24 Enter number of time slots [24]: 3 Configure more channel groups? [no]: y Enter number of time slots [21]: 3 Configure more channel groups? [no]: y Enter number of time slots [18]: 3 Configure more channel groups? [no]: y Enter number of time slots [15]: Configure more channel groups? [no]: Note The following sections describe the prompts for each encapsulation type. No further configuration is needed for HDLC encapsulation. PPP Encapsulation Would you like to enable multilink PPP [yes]: Enter a remote hostname for PPP authentication [Router]: Enter a password for PPP authentication: Note The password, which is used by the Challenge Handshake Authentication Protocol (CHAP) authentication process, is case sensitive and must match the remote router's password exactly. Frame Relay Encapsulation The following lmi-types are available to be set, 2-20 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
2-20
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 2
Using the Setup Command Facility
Configuring Interface Parameters
X.25 Encapsulation
x25 circuit can be either in dce/dte mode.
Choose from either dce/dte [dte]:
Enter local x25 address: 1234
We will need to map the remote x.25 station's x25 address
to the remote stations IP/IPX address
Do you want to map the remote machine's x25 address to IP address? [yes]:
IP address for the remote interface: 6.0.0.1
Do you want to map the remote machine's x25 address to IPX address? [yes]:
IPX address for the remote interface: 40.0060.34c6.90ed
Enter remote x25 address: 4321
Enter lowest 2-way channel [1]:
Enter highest 2-way channel [64]:
Enter frame window (K) [7]:
Enter Packet window (W) [2]:
Enter Packet size (must be powers of 2) [128]:
T1 Channelized Mode
The following is an example of a T1 channelized mode configuration using the
setup
command facility:
The following framing types are available:
esf | sf
Enter the framing type [esf]:
The following linecode types are available:
ami | b8zs
Enter the line code type [b8zs]:
T1 is capable of being configured for channel 1-24
Enter number of time slots [24]: 3
Configure more channel groups? [no]: y
Enter number of time slots [21]: 3
Configure more channel groups? [no]: y
Enter number of time slots [18]: 3
Configure more channel groups? [no]: y
Enter number of time slots [15]:
Configure more channel groups? [no]:
Note
The following sections describe the prompts for each encapsulation type. No further configuration is
needed for HDLC encapsulation.
PPP Encapsulation
Would you like to enable multilink PPP [yes]:
Enter a remote hostname for PPP authentication [Router]:
Enter a password for PPP authentication:
Note
The password, which is used by the Challenge Handshake Authentication Protocol (CHAP)
authentication process, is case sensitive and must match the remote router’s password exactly.
Frame Relay Encapsulation
The following lmi-types are available to be set,