Cisco 3725 Software Configuration Guide - Page 27

Example of the Cisco 3631 Router Interface Numbering

Get Cisco 3725 - PRI Dial Bundle Router PDF manuals and user guides
UPC - 746320810911
View all Cisco 3725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 1 Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering Figure 1-7 Example of the Cisco 3631 Router Interface Numbering Figure 1-7 shows an example of the interface numbering where the following interfaces are installed: • A WIC in each WIC slot (containing interfaces serial 0/0 and serial 0/1 in physical slot W0, and interface serial 0/2 in physical slot W1) • A 32-port asynchronous network module in slot 1 (containing interfaces serial 1/0 through serial 1/31) • An alarm interface controller network module in slot 2 (internally connected to interface serial 2/0) • One built-in Ethernet 10/100 interface-FastEthernet 0/0 Note The logical slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for physical slot identification only.) Interfaces in the WICs are numbered from right to left, starting with 0/0 for each interface type, regardless of which physical slot the WICs are installed in. Some examples are: - If physical slot W0 is empty and physical slot W1 contains a 1-port serial WIC, then the logical interface in the WIC is numbered serial 0/0. - If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, then the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1 and the logical interface in physical slot W1 is numbered Serial 0/2. - If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port BRI WIC, then the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1, and the logical interface in physical slot W1 is numbered BRI 0/0. Some modules have two small slots, labeled W0 and W1, for WAN interface cards. For example, Figure 1-8 shows the W0 and W1 slots of the 2 Ethernet 2 WAN card slot (2E 2-slot) module. You can install WAN interface cards into the small module slots (W0 and W1). Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) WAN interface cards are keyed so that you can install them into slot W1 only. Serial WAN interface cards can be installed into either slot, W0 or W1. OL-1957-04 Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
1-7
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 1
Understanding Interface Numbering and Cisco IOS Software Basics
Understanding Interface Numbering
Figure 1-7
Example of the Cisco 3631 Router Interface Numbering
Figure 1-7
shows an example of the interface numbering where the following interfaces are installed:
•
A WIC in each WIC slot (containing interfaces serial 0/0 and serial 0/1 in physical slot W0, and
interface serial 0/2 in physical slot W1)
•
A 32-port asynchronous network module in slot 1 (containing interfaces serial 1/0 through serial
1/31)
•
An alarm interface controller network module in slot 2 (internally connected to interface serial 2/0)
•
One built-in Ethernet 10/100 interface—FastEthernet 0/0
Note
The logical slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for
physical slot identification only.) Interfaces in the WICs are numbered from right to left, starting with
0/0 for each interface type, regardless of which physical slot the WICs are installed in. Some examples
are:
–
If physical slot W0 is empty and physical slot W1 contains a 1-port serial WIC, then the logical
interface in the WIC is numbered serial 0/0.
–
If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, then
the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1 and the logical
interface in physical slot W1 is numbered Serial 0/2.
–
If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port BRI WIC, then
the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1, and the logical
interface in physical slot W1 is numbered BRI 0/0.
Some modules have two small slots, labeled W0 and W1, for WAN interface cards. For example,
Figure 1-8
shows the W0 and W1 slots of the 2 Ethernet 2 WAN card slot (2E 2-slot) module. You can
install WAN interface cards into the small module slots (W0 and W1). Integrated Services Digital
Network (ISDN) Basic Rate Interface (BRI) WAN interface cards are keyed so that you can install them
into slot W1 only. Serial WAN interface cards can be installed into either slot, W0 or W1.