Cisco 3725 Software Configuration Guide - Page 54

E1 Channelized Mode

Get Cisco 3725 - PRI Dial Bundle Router PDF manuals and user guides
UPC - 746320810911
View all Cisco 3725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Configuring Interface Parameters Chapter 2 Using the Setup Command Facility Configuring the PRI D-channel Would you like to enable multilink PPP? [yes]: Configure IP on this interface? [no]: y Configure IP unnumbered on this interface? [no]: y Assign to which interface [Ethernet0/0]: All users dialing in through the PRI will need to be authenticated using CHAP. The username and password are case sensitive. Enter more username and passwords for PPP authentication? [no]: y Enter the username used for dial-in CHAP authentication [Router]: of the user dialling in on PRI: Enter more username and passwords for PPP authentication? [no]: Enter the PPP password E1 Channelized Mode The following is an example of an E1 channelized mode configuration using the setup command facility: The following framing types are available: no-crc4 | crc4 Enter the framing type [crc4]: The following linecode types are available: ami | hdb3 Enter the line code type [hdb3]: Do you want to configure Serial1/1:0 interface?: [Yes]: Configuring the Channelized E1/T1 serial channels Some encapsulations supported are ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25 Choose encapsulation type [ppp]: Configure IP on this interface? [no]: y Configure IP unnumbered on this interface? [no]: IP address for this interface: 3.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 3.0.0.0, 8 subnet bits; mask is /8 Note The following sections describe the prompts for each encapsulation type. No further configuration is needed for HDLC encapsulation. PPP Encapsulation Would you like to enable multilink PPP [yes]: Enter a remote hostname for PPP authentication [Router]: Enter a password for PPP authentication: Note The password, which is used by the Challenge Handshake Authentication Protocol (CHAP) authentication process, is case sensitive and must match the remote router's password exactly. Frame Relay Encapsulation The following lmi-types are available to be set, when connected to a frame relay switch [0] none 2-18 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
2-18
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 2
Using the Setup Command Facility
Configuring Interface Parameters
Configuring the PRI D-channel
Would you like to enable multilink PPP? [yes]:
Configure IP on this interface? [no]: y
Configure IP unnumbered on this interface? [no]: y
Assign to which interface [Ethernet0/0]:
All users dialing in through the PRI will need to be
authenticated using CHAP. The username and password are
case sensitive.
Enter more username and passwords for PPP authentication? [no]: y
Enter the username used for dial-in CHAP authentication [Router]:
Enter the PPP password
of the user dialling in on PRI:
Enter more username and passwords for PPP authentication? [no]:
E1 Channelized Mode
The following is an example of an E1 channelized mode configuration using the
setup
command facility:
The following framing types are available:
no-crc4 | crc4
Enter the framing type [crc4]:
The following linecode types are available:
ami | hdb3
Enter the line code type [hdb3]:
Do you want to configure Serial1/1:0 interface?: [Yes]:
Configuring the Channelized E1/T1 serial channels
Some encapsulations supported are
ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25
Choose encapsulation type
[ppp]:
Configure IP on this interface? [no]: y
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 3.0.0.1
Subnet mask for this interface [255.0.0.0]:
Class A network is 3.0.0.0, 8 subnet bits; mask is /8
Note
The following sections describe the prompts for each encapsulation type. No further configuration is
needed for HDLC encapsulation.
PPP Encapsulation
Would you like to enable multilink PPP [yes]:
Enter a remote hostname for PPP authentication [Router]:
Enter a password for PPP authentication:
Note
The password, which is used by the Challenge Handshake Authentication Protocol (CHAP)
authentication process, is case sensitive and must match the remote router’s password exactly.
Frame Relay Encapsulation
The following lmi-types are available to be set,
when connected to a frame relay switch
[0] none