Cisco 3725 Software Configuration Guide - Page 111

Configuration Tasks, Con the E1/T1 Network Module for ISDN PRI

Get Cisco 3725 - PRI Dial Bundle Router PDF manuals and user guides
UPC - 746320810911
View all Cisco 3725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Chapter 3 Configuring with the Command-Line Interface Configuring the Digital Modem Network Module for the Cisco 3640 Router Note • The PRI module must be hardware revision -03; earlier revisions are incompatible with digital modem modules. For more information, refer to the "Software and Hardware Requirements" section in the Digital Modem Network Module Configuration Notes. • Install the Digital Modem Network Module in a chassis slot. For information on how to correctly install this network module, refer to the "Installing a Digital Modem Network Module in a Chassis Slot" section in the Digital Modem Network Module Configuration Note. • Complete basic device configuration, including host name, username, protocol, and security configuration. • Make sure that you have the following information: - ISDN PRI Switch type - T1 (or E1) information, such as line code and framing type - Channel-group information and time-slot mapping Configuration Tasks Complete the following tasks to configure the digital modem module interfaces: • Configure the E1/T1 Network Module for ISDN PRI, page 3-51 • Configure the ISDN D-Channel Serial Interfaces, page 3-53 • Configure the Loopback Interface, page 3-54 • Configure the LAN Interface, page 3-55 • Create the Group Asynchronous Interface, page 3-55 • Configure the ISDN Dialer Interface, page 3-56 • Configure the Default IP Pool Information, page 3-57 • Configure Modem Lines for Dial-In and Dial-Out, page 3-57 These tasks are described in the following sections. Configure the E1/T1 Network Module for ISDN PRI The first step in configuring a digital modem interface is to configure ISDN PRI on either a channelized T1 or E1 controller, depending on the ISDN service in your area. The ISDN PRI network modules can have either one or two ports; if the ISDN PRI module installed in your device has two ports, you need to apply the following procedure to both ports. Configure Channelized E1 ISDN PRI To configure ISDN PRI on a channelized E1 controller, perform the following tasks, beginning in global configuration mode: Command Description OL-1957-04 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers 3-51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
3-51
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 3
Configuring with the Command-Line Interface
Configuring the Digital Modem Network Module for the Cisco 3640 Router
Note
•
The PRI module must be hardware revision -03; earlier revisions are incompatible with digital
modem modules. For more information, refer to the “Software and Hardware Requirements” section
in the
Digital Modem Network Module Configuration Notes
.
•
Install the Digital Modem Network Module in a chassis slot. For information on how to correctly
install this network module, refer to the “Installing a Digital Modem Network Module in a Chassis
Slot” section in the
Digital Modem Network Module Configuration Note
.
•
Complete basic device configuration, including host name, username, protocol, and security
configuration.
•
Make sure that you have the following information:
–
ISDN PRI Switch type
–
T1 (or E1) information, such as line code and framing type
–
Channel-group information and time-slot mapping
Configuration Tasks
Complete the following tasks to configure the digital modem module interfaces:
•
Configure the E1/T1 Network Module for ISDN PRI, page 3-51
•
Configure the ISDN D-Channel Serial Interfaces, page 3-53
•
Configure the Loopback Interface, page 3-54
•
Configure the LAN Interface, page 3-55
•
Create the Group Asynchronous Interface, page 3-55
•
Configure the ISDN Dialer Interface, page 3-56
•
Configure the Default IP Pool Information, page 3-57
•
Configure Modem Lines for Dial-In and Dial-Out, page 3-57
These tasks are described in the following sections.
Configure the E1/T1 Network Module for ISDN PRI
The first step in configuring a digital modem interface is to configure ISDN PRI on either a channelized
T1 or E1 controller, depending on the ISDN service in your area. The ISDN PRI network modules can
have either one or two ports; if the ISDN PRI module installed in your device has two ports, you need
to apply the following procedure to both ports.
Configure Channelized E1 ISDN PRI
To configure ISDN PRI on a channelized E1 controller, perform the following tasks, beginning in global
configuration mode:
Command
Description