Dell Precision 490 Desktop User's Guide - Page 129

Replacing the Drive Panel

Get Dell Precision 490 Desktop PDF manuals and user guides View all Dell Precision 490 Desktop manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

NOTE: Hard-drive screws or a hard-drive carrier can be ordered from Dell. See Contacting Dell. 14. If metal shields are present in your computer (see About the Metal Shields Present in Some Drive Configurations), replace metal shields in any empty optical drive bays or over the FlexBay, in tower mode only, by pressing them into place. 15. If a vented metal insert was installed over the FlexBay and you are converting from tower to desktop mode, reinstall it: a. Holding the metal insert at an angle, insert its two upper screws into the slot that runs along the inside of the FlexBay. b. Rotate the bottom of the vented metal insert down and insert its two bottom screws into the slot in the open area beneath the FlexBay. c. Push the vented metal insert until it clicks into place and its metal tabs rest flush against the chassis surface. 1 FlexBay 2 vented metal insert 16. Install the new drive panel (see Replacing the Drive Panel). 17. Replace the computer cover (see Replacing the Computer Cover). 18. Verify that your computer works correctly by running the Dell Diagnostics. Back to Contents Page

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
14.
If metal shields are present in your computer (see
About the Metal Shields Present in Some Drive Configurations
), replace metal shields in any empty
optical drive bays or over the FlexBay, in tower mode only, by pressing them into place.
15.
If a vented metal insert was installed over the FlexBay and you are converting from tower to desktop mode, reinstall it:
a.
Holding the metal insert at an angle, insert its two upper screws into the slot that runs along the inside of the FlexBay.
b.
Rotate the bottom of the vented metal insert down and insert its two bottom screws into the slot in the open area beneath the FlexBay.
c.
Push the vented metal insert until it clicks into place and its metal tabs rest flush against the chassis surface.
16.
Install the new drive panel (see
Replacing the Drive Panel
).
17.
Replace the computer cover (see
Replacing the Computer Cover
).
18.
Verify that your computer works correctly by running the
Dell Diagnostics
.
Back to Contents Page
NOTE:
Hard-drive screws or a hard-drive carrier can be ordered from Dell. See
Contacting Dell
.
1
FlexBay
2
vented metal insert