Dell Unity XT 480 Unity All Flash and Unity Hybrid Unity 480/F Unity 680/F Uni - Page 39

Install a power supply, Service Procedures

Get Dell Unity XT 480 PDF manuals and user guides View all Dell Unity XT 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

2. Push and hold the orange release tab to the left (to the right for the bottom power supply) and grasp the power supply by its handle. Remove the power supply by pulling it from the SP assembly. Figure 33. Removing a power supply Install a power supply About this task The power supplies are installed in the top and bottom SP assemblys, meaning that the top power supply is installed upsidedown. This procedure works for installing either power supply. Steps 1. Align the power supply with the slot in the SP assembly. The power cable retention bail will be on the right for the bottom power supply and on the left for the top power supply. 2. Push the power supply into the SP assembly until it clicks into place. 0 1 2 1 3 XXX XXX XXXX XX REV:XXX Figure 34. Installing a power supply 3. Connect the power cable to the power supply and secure the cord with the retention bail at the connector. Service Procedures 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
2.
Push and hold the orange release tab to the left (to the right for the bottom power supply) and grasp the power supply by
its handle. Remove the power supply by pulling it from the SP assembly.
Figure 33. Removing a power supply
Install a power supply
About this task
The power supplies are installed in the top and bottom SP assemblys, meaning that the top power supply is installed upside-
down. This procedure works for installing either power supply.
Steps
1.
Align the power supply with the slot in the SP assembly. The power cable retention bail will be on the right for the bottom
power supply and on the left for the top power supply.
2.
Push the power supply into the SP assembly until it clicks into place.
0
1
2
3
XXX XXX XXXX XX
REV:XXX
1
Figure 34. Installing a power supply
3.
Connect the power cable to the power supply and secure the cord with the retention bail at the connector.
Service Procedures
39